[c-nsp] 2921 router with 4 port switch

[CiscoNSP List]

You dont have an access-list 1 in your conf (you have "1" in your nat statement) - I assume it is supposed to be "10" based on your conf


> Date: Sun, 1 Dec 2013 11:34:56 -0700
> From: MGlass at lccountymt.gov
> To: cisco-nsp at puck.nether.net
> Subject: [c-nsp] 2921 router with 4 port switch
> 
> I have a 2921 router with a 4 port switch for our internet router, I have our public wireless plugged into the 4 port switch on the router but cannot figure out how to pass traffic outside of the router from our public wireless controller. The public wireless is a tagged from the controller vlan 253, I can ping the vlan ip address but nothing beyond.
>  
> TIA
> Mike
>  
> Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M3, RELEASE SOFTWARE (fc1)
>  
> Here is my current config.
> 
> hostname inet-router
> !
> boot-start-marker
> boot-end-marker
> !
> !
> no logging console
> !
> no aaa new-model
> clock timezone MST -7 0
> clock summer-time MDT recurring
> !
> no ipv6 cef
> ip source-route
> ip cef
> !
> 
> !
> no ip bootp server
> no ip domain lookup
>  
> multilink bundle-name authenticated
> !
> crypto pki token default removal timeout 0
> !
> !
> !
> !
> vtp mode transparent
> !
> !
> vlan 253
> !
>  
> !
> interface Embedded-Service-Engine0/0
>  no ip address
>  shutdown
> !
> interface GigabitEthernet0/0
>  description Interface to PIX Firewall
>  ip address 206.127.2.89 255.255.255.248
>  duplex full
>  speed 1000
> !
> interface GigabitEthernet0/1
>  description Link to MIC DS3 Radio
>  bandwidth 45000
>  ip address 206.127.0.30 255.255.255.252
>  no ip redirects
>  no ip unreachables
>  no ip proxy-arp
>  ip nat outside
>  ip virtual-reassembly in
>  duplex auto
>  speed auto
> !
> interface GigabitEthernet0/0/0
>  description Interface to Cisco Public Wireless
>  switchport trunk allowed vlan 1,253,1002-1005
>  switchport mode trunk
>  no ip address
> !
> interface GigabitEthernet0/0/1
>  no ip address
>  shutdown
> !
> interface GigabitEthernet0/0/2
>  no ip address
>  shutdown
> !
> interface GigabitEthernet0/0/3
>  no ip address
>  shutdown
> !
> interface Vlan1
>  no ip address
>  shutdown
> !
> interface Vlan253
>  ip address 192.168.253.1 255.255.255.0
>  ip nat inside
>  ip virtual-reassembly in
> !
> ip forward-protocol nd
> !
> no ip http server
> no ip http secure-server
> !
> ip nat inside source list 1 interface GigabitEthernet0/0 overload
> ip route 0.0.0.0 0.0.0.0 206.127.1.29
> ip route 206.127.8.0 255.255.255.0 206.127.2.90
> !
> access-list 10 permit 206.127.2.90
> access-list 10 permit 192.168.253.0 0.0.0.255
> dialer-list 1 protocol ip permit
> !
> !
> snmp-server community public RO
> snmp-server enable traps tty
>  
> !
> control-plane
> !
>  
> end
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/