[c-nsp] ASR901 to ME3600X xconnect
Sigurbjörn Birkir Lárusson
sigurbjornl at vodafone.is
Thu Feb 28 18:55:34 EST 2013
Default MTU off the xconnect on the 901 is 9216, could that be your
problem? XConnect won't come up with non-matching MTUs
Kind regards,
Sibbi
On 28.2.2013 21:34, "Pshem Kowalczyk" <pshem.k at gmail.com> wrote:
>Hi,
>
>I'm testing an asr901. We're looking at using for l2vpn termination.
>For some reason the xconnect refuses to stand up between asr901 and
>me3600x. Similar setup between two 3600x works fine.
>
>Relevant config on the asr901:
>
>!
>hostname asr901A
>!
>
>boot system flash:/asr901-universalk9-mz.152-2.SNH1.bin
>
>
>
>mpls label protocol ldp
>mpls ldp discovery targeted-hello accept
>mpls traffic-eng tunnels
>bridge-domain 2
>
>l2 router-id 10.123.129.3
>!
>interface Loopback0
> ip address 10.123.129.3 255.255.255.255
>!
>interface Tunnel3000
> ip unnumbered Loopback0
> mpls ip
> tunnel mode mpls traffic-eng
> tunnel destination 10.123.129.1
> tunnel mpls traffic-eng autoroute announce
> tunnel mpls traffic-eng path-option 1 dynamic
> tunnel mpls traffic-eng record-route
> tunnel mpls traffic-eng fast-reroute
>!
>interface GigabitEthernet0/0
> duplex full
> no negotiation auto
> service instance 1 ethernet
> encapsulation dot1q 17
> rewrite ingress tag pop 1 symmetric
> xconnect 10.123.29.1 4321 encapsulation mpls
> mtu 1500
> !
>!
>interface Vlan2
> mtu 9216
> description to me3600x
> ip address 10.123.29.6 255.255.255.252
> ip router isis vc-core
> mpls traffic-eng tunnels
> clns mtu 9083
> isis network point-to-point
> isis metric 10
>!
>router isis vc-core
> net 49.0001.0101.2312.9003.00
> is-type level-2-only
> ispf level-2
> metric-style wide
> set-overload-bit on-startup wait-for-bgp
> spf-interval 5 50 200
> prc-interval 5 50 200
> lsp-gen-interval 5 50 200
> log-adjacency-changes
> passive-interface default
> no passive-interface Vlan2
> mpls traffic-eng router-id Loopback0
> mpls traffic-eng level-2
>
>
>on the ME3600X the xconnect looks like this:
>
>interface GigabitEthernet0/11
> description not in use
> switchport trunk allowed vlan none
> switchport mode trunk
> mtu 9100
> service-policy output PM-INT-1G-OUT
> service instance 17 ethernet
> encapsulation dot1q 4094
> rewrite ingress tag pop 1 symmetric
> xconnect 10.123.29.3 4321 encapsulation mpls
> mtu 1500
>
>I can see the ISIS and LDP up between asr901 and me3600x:
>
>asr901A#sh mpls ldp neighbor
> Peer LDP Ident: 10.123.129.1:0; Local LDP Ident 10.123.129.3:0
> TCP connection: 10.123.129.1.646 - 10.123.129.3.26629
> State: Oper; Msgs sent/rcvd: 1207/1201; Downstream
> Up time: 17:22:15
> LDP discovery sources:
> Targeted Hello 10.123.129.3 -> 10.123.129.1, active, passive
> Targeted Hello 10.123.129.3 -> 10.123.29.1, active
> Addresses bound to peer LDP Ident:
> 10.123.129.1 10.123.29.5 10.123.29.1
>
>asr901A#sh isis neighbors
>
>Tag vc-core:
>System Id Type Interface IP Address State Holdtime Circuit Id
>accr01cgr L2 Vl2 10.123.29.5 UP 24 01
>
>
>Yet the actual vc doesn't come up:
>
>asr901A#sh mpls l2transport vc detail
>Local interface: Gi0/0 up, line protocol up, Eth VLAN 17 up
> Destination address: 10.123.29.1, VC ID: 4321, VC status: down
> Last error: Local peer access circuit is down
> Output interface: none, imposed label stack {}
> Preferred path: not configured
> Default path: no route
> No adjacency
> Create time: 00:17:34, last status change time: 00:13:54
> Signaling protocol: LDP, peer 10.123.129.1:0 up
> Targeted Hello: 10.123.129.3(LDP Id) -> 10.123.29.1, LDP is DOWN, no
>binding
> Status TLV support (local/remote) : enabled/None (no remote binding)
> LDP route watch : disabled
> Label/status state machine : local ready, LruRnd
> Last local dataplane status rcvd: No fault
> Last BFD dataplane status rcvd: Not sent
> Last BFD peer monitor status rcvd: No fault
> Last local AC circuit status rcvd: No fault
> Last local AC circuit status sent: Not sent
> Last local LDP TLV status sent: No fault
> Last remote LDP TLV status rcvd: None (no remote binding)
> Last remote LDP ADJ status rcvd: None (no remote binding)
> MPLS VC labels: local 16, remote unassigned
> Group ID: local 0, remote unknown
> MTU: local 1500, remote unknown
> Remote interface description:
> Sequencing: receive disabled, send disabled
> Control Word: On (configured: autosense)
> Dataplane:
> SSM segment/switch IDs: 0/0 (used), PWID: 2
> VC statistics:
> transit packet totals: receive 0, send 0
> transit byte totals: receive 0, send 0
> transit packet drops: receive 0, seq error 0, send 0
>
>The error 'Local peer access circuit is down' is all I get on the 901,
>on the me3600x I get:
>accr01cgr#sh mpls l2transport vc 4321 detail
>Local interface: Gi0/11 up, line protocol up, Eth VLAN 4094 down
> Destination address: 10.123.29.3, VC ID: 4321, VC status: down
> Last error: Local peer access circuit is down
> Output interface: none, imposed label stack {}
> Preferred path: not configured
> Default path: no route
> No adjacency
> Create time: 17:49:18, last status change time: 1w3d
> Last label FSM state change time: 17:06:57
> Signaling protocol: LDP, peer unknown
> Targeted Hello: 10.123.129.1(LDP Id) -> 10.123.29.3, LDP is DOWN, no
>binding
> Status TLV support (local/remote) : enabled/None (no remote binding)
> LDP route watch : enabled
> Label/status state machine : local standby, AC-ready, LnuRnd
> Last local dataplane status rcvd: No fault
> Last BFD dataplane status rcvd: Not sent
> Last BFD peer monitor status rcvd: No fault
> Last local AC circuit status rcvd: No fault
> Last local AC circuit status sent: Not sent
> Last local PW i/f circ status rcvd: No fault
> Last local LDP TLV status sent: No status
> Last remote LDP TLV status rcvd: None (no remote binding)
> Last remote LDP ADJ status rcvd: None (no remote binding)
> MPLS VC labels: local 21, remote unassigned
> Group ID: local 0, remote unknown
> MTU: local 1500, remote unknown
> Remote interface description:
> Sequencing: receive disabled, send disabled
> Control Word: On (configured: autosense)
> Dataplane:
> SSM segment/switch IDs: 0/0 (used), PWID: 6
> VC statistics:
> transit packet totals: receive 0, send 0
> transit byte totals: receive 0, send 0
> transit packet drops: receive 0, seq error 0, send 0
>
>Ethernet VLAN is down and the same error message 'Local peer access
>circuit is down' shows up.
>
>Debug on the ASR901 reveals the following:
>*Mar 1 04:02:29.779: AToM[10.123.29.1, 4321]: Receive status update
>*Mar 1 04:02:29.779: AToM[10.123.29.1, 4321]: . Receive AC
>STATUS(DOWN AC(rx/tx faults))
>*Mar 1 04:02:29.779: AToM[10.123.29.1, 4321]: .. AC status DOWN
>AC(rx/tx faults)
>*Mar 1 04:02:29.779: AToM[10.123.29.1, 4321]: ... Local peer access
>circuit is down
>*Mar 1 04:02:29.779: AToM[10.123.29.1, 4321]: .... S:Evt local down in
>LndRnd
>*Mar 1 04:02:29.779: AToM[10.123.29.1, 4321]: ..... NMS: VC oper state:
>DOWN
>*Mar 1 04:02:29.783: AToM[10.123.29.1, 4321]: ..... NMS: err
>codes: loc-ac-rx-err
>*Mar 1 04:02:29.783: AToM[10.123.29.1, 4321]: ..... NMS:
>: + loc-ac-tx-err
>*Mar 1 04:02:29.783: AToM[10.123.29.1, 4321]: ..... SYSLOG: VC is
>DOWN, Loc AC Err
>*Mar 1 04:02:29.783: AToM[10.123.29.1, 4321]: ... Local ready
>*Mar 1 04:02:29.783: AToM[10.123.29.1, 4321]: ... Local service is
>ready; send a label
>
>I have no idea why I get those errors on the AC.
>Any hints will be greatly appreciated.
>
>kind regards
>Pshem
>_______________________________________________
>cisco-nsp mailing list cisco-nsp at puck.nether.net
>https://puck.nether.net/mailman/listinfo/cisco-nsp
>archive at http://puck.nether.net/pipermail/cisco-nsp/
More information about the cisco-nsp
mailing list