[c-nsp] Cisco s0/1/0 T-1 is up but not showing up in route table
false
jctx09 at yahoo.com
Wed Jan 30 17:52:20 EST 2013
The T-1 seems to be up from a Layer-2 perspective. Something is wrong with my routing though. The interface does NOT show up in the “sh ip route? Output. I would expect to see it as a directly connected interface but it isn't there. The card is in “slot 1” so I’m thinking that may have something to do with but that’s just a hunch. We also have a 9-port switch in the router as well. “Sh diag” looks clean too. Any ideas?
router#sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is x.x.92.1 to network 0.0.0.0
x.0.0.0/24 is subnetted, 1 subnets
C x.x.92.0 is directly connected, FastEthernet0/0
S 192.168.10.0/24 [1/0] via 192.168.2.3
172.16.0.0/30 is subnetted, 1 subnets
C 172.16.31.48 is directly connected, Tunnel21
172.18.0.0/24 is subnetted, 2 subnets
S 172.18.3.0 [1/0] via 192.168.2.254
S 172.18.1.0 [1/0] via 192.168.2.254
S 192.168.1.0/24 [1/0] via 192.168.2.254
C 192.168.2.0/24 is directly connected, Vlan10
S 192.168.3.0/24 [1/0] via 192.168.2.254
S* 0.0.0.0/0 [1/0] via x.x.92.1
router#
T-1 looks good here, plus no Alarms
router#sh service-module serial 0/1/0
Interface Serial0/1/0
Module type is T1/fractional
Hardware revision is 1.0, Software revision is 001,
Image checksum is 0x0, Protocol revision is 0.1
Receiver has no alarms.
Framing is ESF, Line Code is B8ZS, Current clock source is line,
Fraction has 24 timeslots (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec.
Last module self-test (done at startup): Passed
Last clearing of alarm counters 00:17:16
loss of signal : 0,
loss of frame : 0,
AIS alarm : 0,
Remote alarm : 0,
Module access errors : 0,
Total Data (last 0 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in current interval (0 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
router#
sh ver
System image file is "flash:c2801-adventerprisek9-mz.124-24.T.bin"
Cisco 2801 (revision 7.0) with 240640K/21504K bytes of memory.
Processor board ID FTX1046Z0J0
11 FastEthernet interfaces
1 Serial interface
1 terminal line
1 Virtual Private Network (VPN) Module
2 DSPs, 16 Voice resources
1 cisco service engine(s)
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)
interface Serial0/1/0
ip address x.x.x.x 255.255.255.252
encapsulation ppp
service-module t1 timeslots 1-24
end
More information about the cisco-nsp
mailing list