[c-nsp] 7609 %CONST_DIAG-SP-3-HM_TEST_FAIL

[Chris Lane]

New line card inserted about a week ago, along with a new 10g service. Last
night the LC crashed with the following;

000504: May 17 03:41:24.011 CDT: %CONST_DIAG-SP-3-HM_TEST_FAIL: Module 4
TestMacNotification consecutive failure count:5
000505: May 17 03:41:24.015 CDT: %CONST_DIAG-SP-6-HM_TEST_SP_INFO:
TestMacNotification[4]: last_busy_percent[13%], Tx_Rate[577], Rx_Rate[46]
000508: May 17 03:42:17.500 CDT: %LINK-3-UPDOWN: Interface
TenGigabitEthernet4/1, changed state to down
000509: May 17 03:42:17.504 CDT: %LINEPROTO-5-UPDOWN: Line protocol on
Interface TenGigabitEthernet4/1, changed state to down
000510: May 17 03:42:17.628 CDT: %SNMP-5-MODULETRAP: Module 4 [Down] Trap
000511: May 17 03:42:17.476 CDT: %CONST_DIAG-SP-2-HM_LC_CRSH: Module 4
crashed due to unrecoverable errors, Reason: Failed TestFabricCh1Health
000512: May 17 03:42:17.632 CDT: %C6KPWR-SP-4-DISABLED: power to module in
slot 4 set off (Diagnostic Failure)
000513: May 17 03:42:17.752 CDT: %LINK-SP-3-UPDOWN: Interface
TenGigabitEthernet4/1, changed state to down
000514: May 17 03:42:17.876 CDT: %HA_EM-6-LOG: Mandatory.go_fabrich1.tcl:
GOLD EEM TCL policy for TestFabricCh1Health
000515: May 17 03:42:17.756 CDT: %LINEPROTO-SP-5-UPDOWN: Line protocol on
Interface TenGigabitEthernet4/1, changed state to down

s72033-advipservicesk9_wan-mz.122-33.SXH7.bin

sh mod
Mod Ports Card Type                              Model              Serial
No.
--- ----- -------------------------------------- ------------------
-----------
  1   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX
SAL1405ACTW
  3   16  SFM-capable 16 port 1000mb GBIC        WS-X6516-GBIC
 SAD050603XM
  4    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE
 SAL1338Z6Z2
  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3BXL
SAD084805W5

Mod MAC addresses                       Hw    Fw           Sw
Status
--- ---------------------------------- ------ ------------ ------------
-------
  1  8843.e1b6.f950 to 8843.e1b6.f97f   3.4   12.2(18r)S1  12.2(33)SXH7 Ok
  3  0001.63d0.e11e to 0001.63d0.e12d   2.0   6.1(3)       8.7(0.22)BUB Ok
  4  0027.0d34.f7bc to 0027.0d34.f7bf   3.0   12.2(14r)S5  12.2(33)SXH7
PwrDown
  5  0011.21a1.5680 to 0011.21a1.5683   4.1   8.1(3)       12.2(33)SXH7 Ok

Mod  Sub-Module                  Model              Serial       Hw
Status
---- --------------------------- ------------------ ----------- -------
-------
  1  Centralized Forwarding Card WS-F6700-CFC       SAL1406AS70  4.1    Ok
  4  Distributed Forwarding Card WS-F6700-DFC3BXL   SAL1333W4UP  5.5
 PwrDown
  5  Policy Feature Card 3       WS-F6K-PFC3BXL     SAD084806L7  1.4    Ok
  5  MSFC3 Daughterboard         WS-SUP720          SAD084307B8  2.2    Ok

Mod  Online Diag Status
---- -------------------
  1  Pass
  3  Pass
  4  Not Applicable
  5  Pass

I have read in many earlier threads it could be the SUP the chassis and
just a simple reseating of the card.

Does anyone have the clear picture here?

 Thanks so much for looking



-- 
//CL