[c-nsp] ASR1001 not forwarding traffic

[Patrick Longomba]

Hi Ali,

Could you send us the output of the "show platform".
I would like to check the version of your line card.
Thanks


Patrick


2014-08-04 7:40 GMT+02:00 Ali Sumsam <ali+cisconsp at eintellego.net>:

> Hi All,
>
> I have bought a new CiscoASR1001. Just configured it as a PPPoE server with
> simplest configuration. My PPPoE client connects successfully, gets
> authenticated and gets the IP address. But packet are not forwarded if I
> try to ping internet or even the ASR from the PPPoE client.
>
>
> The same configuration works fine on a Cisco IOS router, If I make it a
> PPPoE server.
>
> Do I need to enable something on my ASR1001? or am I using a wrong IOS
> version?
>
>
> Source of my configuration is
>
> http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/bbdsl/configuration/xe-3s/asr1000/bba-xe-3s-asr1000-book/bba-pppoe-client-xe.html#GUID-91AF32F2-662D-4EF8-99DD-37C021637AE7
>
>
> Device> *enable*
> Device# *configure terminal*
> Device(config)# *interface GigabitEthernet 0/0/0*
> Device(config-if)# *no ip address*
> Device(config-if)# *pppoe enable*
> Device(config-if)# *pppoe-client dial-pool-number 1*
> Device(config-if)# *no shutdown*
> Device(config-if)# *exit*
> Device(config)# *interface dialer 1*
> Device(config-if)# *mtu 1492*
> Device(config-if)# *ip address negotiated*
> Device(config-if)# *encapsulation ppp*
> Device(config-if)# *dialer pool 1*
> Device(config-if)# *ppp pap sent-username username1 password password1*
> Device(config-if)# *end*
>
> Example: Configuring PPPoE on IPv4
>
> Example: Server Configuration
>
> Device> *enable*
> Device# *configure terminal*
> Device# *username username1 password password1*
> Device(config)# *bba-group pppoe bba1*
> Device(config-bba-group)# *virtual-template 1*
> Device(config-bba-group)# *exit*
> Device(config)# *interface loopback 1*
> Device(config-if)# *ip address 192.2.0.2 255.255.255.0*
> Device(config-if)# *exit*
> Device(config)# *interface GigabitEthernet 0/0/0*
> Device(config-if)# *no ip address*
> Device(config-if)# *negotiation auto*
> Device(config-if)# *pppoe enable group bba1*
> Device(config-if)# *no shutdown*
> Device(config-if)# *exit*
> Device(config)# *interface virtual-template 1*
> Device(config-if)# *description pppoe bba1*
> Device(config-if)# *mtu 1492*
> Device(config-if)# *ip unnumbered loopback 1*
> Device(config-if)# *peer default ip address pool pool1*
> Device(config-if)# *ppp authentication pap*
> Device(config-if)# *exit*
> Device(config)# *ip local pool pool1 192.2.0.1 192.2.0.10*
> Device(config)# *end*
>
>
>
> #show version
> Cisco IOS XE Software, Version 03.11.00.S - Standard Support Release
> Cisco IOS Software, ASR1000 Software (X86_64_LINUX_IOSD-UNIVERSALK9-M),
> Version 15.4(1)S, RELEASE SOFTWARE (fc2)
>
>
> ROM: IOS-XE ROMMON
>
> System image file is
> "bootflash:/asr1001-universalk9.03.11.00.S.154-1.S-std.bin"
> Last reload reason: Reload Command
>
>
> License Level: ipbase
> License Type: Default. No valid license found.
> Next reload license Level: ipbase
>
> cisco ASR1001 (1RU) processor with 6848982K/6147K bytes of memory.
> Processor board ID SSI181608S5
> 4 Gigabit Ethernet interfaces
> 32768K bytes of non-volatile configuration memory.
> 16777216K bytes of physical memory.
> 7741439K bytes of eUSB flash at bootflash:.
> 999424K bytes of USB flash at usb0:.
>
> Configuration register is 0x2102
>
>
>
> Regards,
>
> *Ali Sumsam  - *eintellego Networks Pty Ltd
> Senior Network Engineer
> ali at eintellegonetworks.com ; www.eintellegonetworks.com
>
> Phone: 1300 239 038; Cell +61 (0)450 609 592 ; skype://sumsam.ali80
>
> facebook.com/eintellegonetworks ;  <http://twitter.com/networkceoau>
> linkedin.com/in/alisumsam
>
>
> The Experts Who The Experts Call
> Juniper - Cisco - Cloud
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>