[c-nsp] ASR 1K : EFP / XCONNECT / BDI
Nicolas KARP
liste at karp.fr
Wed Dec 3 09:54:06 EST 2014
That's the point !! I modified the mtu under the bdi interface and i had to
modify the mu under the l2 vfi interface in order to get it funtionnal.
Thanks for the help.
# - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - -
# - - Nicolas KARP
# - - Network and Security Engineer
# - - Email : liste at karp.fr <nicolas at karp.fr>
# - - Linkedin : http://www.linkedin.com/in/nicolaskarp
# - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp
<http://www.viadeo.com/fr/profile/nicolas.karp%20>
# - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - -
2014-12-03 13:13 GMT+01:00 Vitkovský Adam <adam.vitkovsky at swan.sk>:
> Does the MTU match on both ends please?
>
> You can see the MTU on both ends in the output of the cmd “sh mpls l2 vc
> det”
>
>
>
> adam
>
>
>
> *From:* nicolas at karp.fr [mailto:nicolas at karp.fr] *On Behalf Of *Nicolas
> KARP
> *Sent:* Wednesday, December 03, 2014 12:29 PM
> *To:* Vitkovský Adam
> *Cc:* cisco-nsp at puck.nether.net
> *Subject:* Re: [c-nsp] ASR 1K : EFP / XCONNECT / BDI
>
>
>
> I've found another thread where you were talking about router pw on an
> ASR1k.
>
>
>
> He is the config i've done so far :
>
>
>
> *ASR 1001X : *
>
>
>
> l2 vfi TEST2 manual
>
> vpn id 258
>
> bridge-domain 4093
>
> neighbor 2.2.2.2 11 encapsulation mpls
>
>
>
> interface BDI4093
>
> mtu 1530
>
> ip vrf forwarding TEST2
>
> ip address 172.31.0.253 255.255.255.0
>
> standby 1 ip 172.31.0.254
>
> standby 1 priority 110
>
> standby 1 preempt delay minimum 60
>
> end
>
>
>
> interface GigabitEthernet0/0/4
>
> no ip address
>
> load-interval 30
>
> negotiation auto
>
> service instance 4093 ethernet
>
> encapsulation dot1q 4093 exact
>
> rewrite ingress tag pop 1 symmetric
>
> bridge-domain 4093
>
> !
>
>
>
>
>
> *ISR 2801 : *
>
>
>
> interface FastEthernet0/1.4093
>
> encapsulation dot1Q 4093
>
> no cdp enable
>
> xconnect 1.1.1.1 11 encapsulation mpls
>
>
>
>
>
> //
>
>
>
> For some reason the xconnect is not coming up...
>
>
>
>
>
> RTI-MPLS-SAB-01#sh xconnect all
>
> DN pri vfi OCTEY UP mpls 2.2.2.2:11
> DN
>
> UP pri bd 4093 UP vfi TEST2
> UP
>
>
>
>
>
> Thanks for your help.
>
>
>
>
> # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> - - - - - - - - - - - - - - - - - - - - -
> # - - Nicolas KARP
> # - - Network and Security Engineer
> # - - Email : liste at karp.fr <nicolas at karp.fr>
> # - - Linkedin : http://www.linkedin.com/in/nicolaskarp
> # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp
> <http://www.viadeo.com/fr/profile/nicolas.karp%20>
> # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> - - - - - - - - - - - - - - - - - - - -
>
>
>
> 2014-12-03 11:14 GMT+01:00 Nicolas KARP <liste at karp.fr>:
>
> Hi Adam,
>
>
>
> I don't have the xconnect command under the bdi interface :
>
>
>
> RTI-MPLS-SAB-01(config)#interface BDI4093
>
> RTI-MPLS-SAB-01(config-if)#xconnect ?
>
> % Unrecognized command
>
>
>
> I'm using ASR1001X , ves 03.13.01.S
>
>
>
>
>
> Any thought ?
>
>
>
>
>
>
> # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> - - - - - - - - - - - - - - - - - - - - -
> # - - Nicolas KARP
> # - - Network and Security Engineer
> # - - Email : liste at karp.fr <nicolas at karp.fr>
> # - - Linkedin : http://www.linkedin.com/in/nicolaskarp
> # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp
> <http://www.viadeo.com/fr/profile/nicolas.karp%20>
> # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> - - - - - - - - - - - - - - - - - - - -
>
>
>
> 2014-12-03 10:21 GMT+01:00 Vitkovský Adam <adam.vitkovsky at swan.sk>:
>
> Hi Nicolas,
>
> This is the config for mixing EFPs and PWs in a common BD + IP interface
> for the BD.
> Manual hub and spoke type of configuration with IP address + VFR at the
> hub location.
>
> interface TenGigabitEthernet0/3
> mtu 9000
> service instance 8000 ethernet
> description CUSTOMER-B
> encapsulation dot1q 20,30,40
> rewrite ingress tag pop 1 symmetric
> bridge-domain 8000
>
> interface BDI8000
> mtu 9000
> vrf CUST-B
> ip add 192.0.2.1 255.255.255.0
> xconnect vfi CUST-B-BD
>
> l2 vfi CUST-B-BD manual
> vpn id 1
> neighbor 10.0.1.3 100 encapsulation mpls
> neighbor 10.0.1.4 200 encapsulation mpls
> neighbor 10.0.1.5 300 encapsulation mpls
>
> Spokes would have just EFPs with xconnect.
>
>
> adam
> > -----Original Message-----
> > From: cisco-nsp [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of
> > Nicolas KARP
> > Sent: Tuesday, December 02, 2014 6:03 PM
> > To: cisco-nsp at puck.nether.net
> > Subject: [c-nsp] ASR 1K : EFP / XCONNECT / BDI
> >
> > Hi,
> >
> > I need to interconnect 2 platforms on 2 different datacenters.
> >
> > The idea is to create several EFPs on each PE (one at each side) and
> create a
> > default xconnect pw in order to encapsulate the layer2 traffic over our
> MPLS
> > network. I also have some layer 3 interfaces for different vlans which
> need to
> > be used on both datacenters :
> >
> >
> > *PE1 : (same config on PE2, except for the BDI interface)*
> >
> >
> > *interface GigabitEthernet0/0/4*
> > * no ip address*
> > * load-interval 30*
> > * negotiation auto*
> >
> > *## default XCONNECT to DC2*
> > * service instance 1 ethernet*
> > * encapsulation default*
> > * xconnect 1.1.1.1 9999 encapsulation mpls pw-class EOMPLS-ETH-TO-VLAN*
> > * !*
> >
> > *## Layer 3 interface via BDI*
> > * service instance 4093 ethernet*
> > * encapsulation dot1q 4093 exact*
> > * rewrite ingress tag pop 1 symmetric*
> > * bridge-domain 4093*
> > * !*
> >
> > *interface BDI4093*
> > * ip vrf forwarding TEST2*
> > * ip address 172.31.0.253 255.255.255.0*
> > * standby 1 ip 172.31.0.254*
> > * standby 1 priority 110*
> > * standby 1 preempt delay minimum 60*
> > *end*
> >
> > *--> I'm missing a xconnect for the vlan 4093...*
> >
> >
> > How can I create a layer3 interface and run a xconnect on the same EFP ?
> > The idea would be to use the same vlans at both locations and terminate
> the
> > Layer3 on a BDI interface in Datacenter1.
> >
> > Do you think it's possible ?
> > I'm not too sure if i'm really clear. Don't hesitate to ask me if you
> have any
> > questions :)
> >
> > Many Thanks for your help !
> >
> > # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> - -
> > - - - - - - - - - - - - - - - - - - -
> > # - - Nicolas KARP
> > # - - Network and Security Engineer
> > # - - Email : liste at karp.fr <nicolas at karp.fr>
> > # - - Linkedin : http://www.linkedin.com/in/nicolaskarp
> > # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp
> > <http://www.viadeo.com/fr/profile/nicolas.karp%20>
> > # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> - -
> > - - - - - - - - - - - - - - - - - - -
> > _______________________________________________
> > cisco-nsp mailing list cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
>
>
>
>
>
More information about the cisco-nsp
mailing list