[c-nsp] ASR903 AToM

[Mohammad Khalil]

I have applied the configuration and The same 
The circuit is up but no ping between the CEs 
I issued the command show monitor event-trace atom and mismatched c-bit message appeared 

From: Adam.Vitkovsky at gamma.co.uk
To: eng_mssk at hotmail.com; cisco-nsp at puck.nether.net
Subject: RE: [c-nsp] ASR903 AToM
Date: Sun, 19 Apr 2015 09:10:40 +0000

Hi Mohamad,



I'm not sure if this "new-style" config works yet.



This is how it would look like using the "old-style"



ASR903

interface GigabitEthernet0/0/0

  service instance trunk 1 ethernet

    encapsulation dot1q 100,200,300

    rewrite ingress tag pop 1 symmetric

    xconnect 2.2.2.2 20 encapsulation mpls



! interface GigabitEthernet0/1/0

!  service instance trunk 1 ethernet

!    encapsulation dot1q 100,200,300

!    rewrite ingress tag pop 1 symmetric

!    xconnect 2.2.2.2 40 encapsulation mpls

! -- config related to backup PW-- 



Also on ME I'd recommend using xconnect under the service instance rather than attaching the service instance to a BD and configuring xconnect under the VLAN interface. Because if you attach a service instance to a BD by default MAC learning is in place and you don't want that for a simple p2p PW (MAC learning can be disabled using cmd: " no mac learning" under the BD config).



ME3600

interface GigabitEthernet0/x

  service instance trunk 1 ethernet

    encapsulation dot1q 100,200,300

    rewrite ingress tag pop 1 symmetric

    xconnect 1.1.1.1 20 encapsulation mpls

!     backup peer 1.1.1.1 40 encapsulation mpls

! -- config related to backup PW--



adam

> -----Original Message-----

> From: cisco-nsp [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of

> Mohammad Khalil

> Sent: 18 April 2015 01:08

> To: cisco-nsp at puck.nether.net

> Subject: [c-nsp] ASR903 AToM

> 

> Hi all

> I have the below setup

> I have ASR903 connected to ME3600 (both are acting as PEs)

> The ASR903 is part of REP ring consisting of other 3400 switches with ASR903

> being the primary

> I have two CEs , one is directly connected to the ME3600 box , and the other

> CE is connected to one of the 3400 switches which are part of the REP ring

> What am trying to do is to establish AToM (Xconnect) between the two CEs

> The Vlan used for testing is 100 (there are other Vlans passing through the

> trunks that are not for MPLS service)

> 

> ASR903

> interface GigabitEthernet0/0/0

>  description Connected-To-AS1-G0/2

>  no ip address

>  negotiation auto

>  rep segment 20 edge primary

>  rep preempt delay 30

>  rep block port 3 vlan 1-4094

>  service instance trunk 1 ethernet

>   encapsulation dot1q 100,200,300

>   rewrite ingress tag pop 1 symmetric

>   bridge-domain from-encapsulation

> 

> 

> interface GigabitEthernet0/1/0

>  description Connected-To-AS2-G0/2

>  no ip address

>  negotiation auto

>  rep segment 20 edge preferred

>  rep preempt delay 30

>  service instance trunk 1 ethernet

>   encapsulation dot1q 100,200,300

>   rewrite ingress tag pop 1 symmetric

>   bridge-domain from-encapsulation

> 

> interface pseudowire 20

> encapsulation mpls

> neighbor 2.2.2.2 20

> 

> l2vpn xconnect context L2VPN

> member GigabitEthernet0/0/0 --> When I tried to put service-instance , it did

> not accept the command

> member pseudowire 20

> 

> ME3600

> interface vlan 100

> no ip address

> xconnect 1.1.1.1 20 encapsulation mpls

> 

> Now , the xconnect came up as shown in the output below

> 

> ME3600X#show mpls l2transport vc 20

> 

> Local intf     Local circuit              Dest address    VC ID      Status

> -------------  -------------------------- --------------- ---------- ----------

> Vl100          Eth VLAN 100               1.1.1.1         20         UP

> 

> ASR903#sh xconnect all

> Legend:    XC ST=Xconnect State  S1=Segment1 State  S2=Segment2 State

>   UP=Up       DN=Down            AD=Admin Down      IA=Inactive

>   SB=Standby  HS=Hot Standby     RV=Recovering      NH=No Hardware

> 

> XC ST  Segment 1                         S1 Segment 2                         S2

> ------+---------------------------------+--+---------------------------------+--

> UP pri mpls 2.2.2.2:20                   UP   ac Gi0/0/0:6(Ethernet)          UP

> 

> No ping between the two sites , I tried to modify the MTU vlaue on the

> interfaces going to the CE side , and the xconnect is down directly

> I have tested L3VPN using the exact same setup (without modifying the MTU

> values on any interface) and it worked fine

> 

> Any ideas?

> 

> Thanks in advance

> 

> BR,

> Mohammad

> 

> _______________________________________________

> cisco-nsp mailing list  cisco-nsp at puck.nether.net

> https://puck.nether.net/mailman/listinfo/cisco-nsp

> archive at http://puck.nether.net/pipermail/cisco-nsp/



  This email has been scanned for email related threats and delivered safely by Mimecast.
 For more information please visit http://www.mimecast.com