[c-nsp] ASR903 dir Error

[Mohammad Khalil]

Hi Adam
Thanks for the reply 
Yes i installed the functioning RSP in the lower slot , but actually i did not wait for 45 minutes :)
I will give it a last try 

Thanks again

BR,
Mohammad

From: Adam.Vitkovsky at gamma.co.uk
To: eng_mssk at hotmail.com; cisco-nsp at puck.nether.net
Subject: RE: [c-nsp] ASR903 dir Error
Date: Tue, 24 Mar 2015 10:17:59 +0000









Hi Mohammad,
 
If you try to boot the box with just that one RSP in it, the RSP should be in the bottom slot I guess.
Do you have another RSP you could use to boot the box?
If the box is fully booted with the spare RSP you could try to insert this faulty RSP to see if it will sync up successfully or it’s
 dead indeed.
Please not the sync up process may take even 45 minutes these CPUs are very very slow.  
 
adam



From: Mohammad Khalil [mailto:eng_mssk at hotmail.com]


Sent: 24 March 2015 07:31

To: Adam Vitkovsky; cisco-nsp at puck.nether.net

Subject: RE: [c-nsp] ASR903 dir Error


 

Hi Adam

I have tried to do what you proposed but the same happened , I got the log message below when I tried


WARNING: Peer RP not present, will not check peer installation state.

% Error connecting to RP 1



BR,

Mohammad




From:
Adam.Vitkovsky at gamma.co.uk

To: eng_mssk at hotmail.com; 
cisco-nsp at puck.nether.net

Subject: RE: [c-nsp] ASR903 dir Error

Date: Thu, 19 Mar 2015 00:31:59 +0000



Hi Mohammad,



Try to remove all line-cards and possibly backup RSP as well leaving just the primary RSP in the chases and start the box.


Once the RSP is booted try to insert the second one.

And do the SW upgrade before you insert the interface cards - or you can upgrade just the primary RSP and then you can insert additional HW.


I recall this happened with the early versions of the code for A903s. 





adam

> -----Original Message-----

> From: cisco-nsp [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of

> Mohammad Khalil

> Sent: 18 March 2015 07:16

> To: cisco-nsp at puck.nether.net

> Subject: [c-nsp] ASR903 dir Error

> 

> Hi

> I have Cisco ASR 903 with two RSPs

> When I console to one for the RSPs , i am in the rommon mode

> When I try to browse for the bootflash , I get the below message

> rommon 1 > dir bootflash:

> 

> ERROR:: PRSSTAT.BREN is NOT set. Data xfr incomplete

> 

> FAILURE

> prsstat ff8d0206 not ESDHC_PRSSTAT_BREN i=

> 0esdhc_wait_for_status_clr(556) ERR: bitmask=0x00000002 not clr PRSSTAT =

> 0xff8d0206 i=100000

> sd_read_sector(1464) failed

> Disk Error : Unable to read the drive'spartition table

> 

> From the other RSP , when I issue the show platform command , the same

> RSP show as unknown

> 

> Any ideas?

> 

> BR,

> Mohammad

> 

> 

> _______________________________________________

> cisco-nsp mailing list cisco-nsp at puck.nether.net

> https://puck.nether.net/mailman/listinfo/cisco-nsp

> archive at 
http://puck.nether.net/pipermail/cisco-nsp/







This email has been scanned for email related threats and delivered safely by Mimecast.

For more information please visit 
http://www.mimecast.com 









  This email has been scanned for email related threats and delivered safely by Mimecast.
 For more information please visit http://www.mimecast.com