[c-nsp] AToM
Christophe Lucas
christophe at clucas.fr
Thu Mar 26 06:41:19 EDT 2015
Dear,
Perhaps I will say mistakes, but I can read :
7613#sh mpls l2transport vc 7232183 detail
Local interface: Vl183 up, line protocol up, Eth VLAN 183 up
Interworking type is Ethernet
Destination address: 172.20.40.232, VC ID: 7232183, VC status: up
Output interface: none, imposed label stack {}
Preferred path: not configured
Default path: active
No adjacency
=> For me it is not correct.
On your 3600 :
3600#sh mpls l2transport vc 7232183 detail
Local interface: Vl183 up, line protocol up, Eth VLAN 183 up
Interworking type is Ethernet
Destination address: 172.20.40.7, VC ID: 7232183, VC status: down
Last error: Remote peer access circuit is down
Output interface: Vl925, imposed label stack {281}
Preferred path: not configured
Default path: active
Next hop: 172.20.202.49
Regards,
Christophe
Le 2015-03-24 09:00, Mohammad Khalil a écrit :
> 3600#sh mpls l2transport vc 7232183 detail
> Local interface: Vl183 up, line protocol up, Eth VLAN 183 up
> Interworking type is Ethernet
> Destination address: 172.20.40.7, VC ID: 7232183, VC status: down
> Last error: Remote peer access circuit is down
> Output interface: Vl925, imposed label stack {281}
> Preferred path: not configured
> Default path: active
> Next hop: 172.20.202.49
> Create time: 02:59:58, last status change time: 00:00:02
> Last label FSM state change time: 00:01:38
> Signaling protocol: LDP, peer 172.20.40.7:0 up
> Targeted Hello: 172.20.40.232(LDP Id) -> 172.20.40.7, LDP is UP
> Graceful restart: not configured and not enabled
> Non stop routing: not configured and not enabled
> Status TLV support (local/remote) : enabled/supported
> LDP route watch : enabled
> Label/status state machine : established, LruRrd
> Last local dataplane status rcvd: No fault
> Last BFD dataplane status rcvd: Not sent
> Last BFD peer monitor status rcvd: No fault
> Last local AC circuit status rcvd: No fault
> Last local AC circuit status sent: DOWN AC(rx/tx faults)
> Last local PW i/f circ status rcvd: No fault
> Last local LDP TLV status sent: No fault
> Last remote LDP TLV status rcvd: DOWN AC(rx/tx faults)
> Last remote LDP ADJ status rcvd: No fault
> MPLS VC labels: local 2042, remote 281
> Group ID: local 0, remote 0
> MTU: local 1500, remote 1500
> Remote interface description: AMAAL_TEST
> Sequencing: receive disabled, send disabled
> Control Word: On (configured: autosense)
> Dataplane:
> SSM segment/switch IDs: 475811/242336 (used), PWID: 44
> VC statistics:
> transit packet totals: receive 0, send 16
> transit byte totals: receive 0, send 1200
> transit packet drops: receive 0, seq error 0, send 0
>
> 7613#sh mpls l2transport vc 7232183 detail
> Local interface: Vl183 up, line protocol up, Eth VLAN 183 up
> Interworking type is Ethernet
> Destination address: 172.20.40.232, VC ID: 7232183, VC status: up
> Output interface: none, imposed label stack {}
> Preferred path: not configured
> Default path: active
> No adjacency
> Create time: 03:12:56, last status change time: 00:00:03
> Signaling protocol: LDP, peer 172.20.40.232:0 up
> Targeted Hello: 172.20.40.7(LDP Id) -> 172.20.40.232, LDP is UP
> Status TLV support (local/remote) : enabled/supported
> LDP route watch : enabled
> Label/status state machine : established, LrdRru
> Last local dataplane status rcvd: No fault
> Last local SSS circuit status rcvd: DOWN AC(rx/tx faults)
> Last local SSS circuit status sent: No fault
> Last local LDP TLV status sent: DOWN AC(rx/tx faults)
> Last remote LDP TLV status rcvd: No fault
> Last remote LDP ADJ status rcvd: No fault
> MPLS VC labels: local 281, remote 2042
> Group ID: local 0, remote 0
> MTU: local 1500, remote 1500
> Remote interface description: AMAAL_TEST
> Sequencing: receive disabled, send disabled
> Control Word: On (configured: autosense)
> VC statistics:
> transit packet totals: receive 16, send 0
> transit byte totals: receive 960, send 0
> transit packet drops: receive 0, seq error 0, send 0
>
>
>> To: cisco-nsp at puck.nether.net
>> From: mark.tinka at seacom.mu
>> Date: Tue, 24 Mar 2015 09:54:47 +0200
>> Subject: Re: [c-nsp] AToM
>>
>>
>>
>> On 24/Mar/15 09:49, Mohammad Khalil wrote:
>> > Hi all
>> > I am trying to establish AToM between 7613 and 3600
>> > The module from the 7613 side is 7600 ES+ 20xGE SFP
>> >
>> > 3600#sh run int vlan 183
>> > interface Vlan183
>> > no ip address
>> > xconnect 172.20.40.7 7232183 encapsulation mpls
>> >
>> > 7613#sh run int vlan 183
>> > interface Vlan183
>> > no ip address
>> > load-interval 30
>> > xconnect 172.20.40.232 7232183 encapsulation mpls
>> >
>> > 7613#sh mpls l2transport vc 7232183
>> >
>> > Local intf Local circuit Dest address VC ID Status
>> > ------------- -------------------------- --------------- ---------- ----------
>> > Vl183 Eth VLAN 183 172.20.40.232 7232183 UP
>> >
>> > 3600#sh mpls l2transport vc 7232183
>> >
>> > Local intf Local circuit Dest address VC ID Status
>> > ------------- -------------------------- --------------- ---------- ----------
>> > Vl183 Eth VLAN 183 172.20.40.7 7232183 DOWN
>> >
>> > I have tried to configure L3VPN (VRF on both routers and test loopback interfaces) and it worked fine
>> >
>> > Any ideas?
>>
>> Detailed output?
>>
>> Mark.
>> _______________________________________________
>> cisco-nsp mailing list cisco-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
> _______________________________________________
> cisco-nsp mailing list cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
--
Christophe Lucas
http://www.clucas.fr/blog/
More information about the cisco-nsp
mailing list