[c-nsp] Cisco Juniper Xconnect
Mohammad Khalil
eng_mssk at hotmail.com
Sun Apr 24 07:46:39 EDT 2016
Thanks dear
I have removed the below lines
R2 (CE connected to Cisco)
R2#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 192.168.23.2 - c202.1a7c.0000 ARPA FastEthernet0/0.23
Internet 192.168.23.3 0 Incomplete ARPA
R3#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 192.168.23.2 0 c202.1a7c.0000 ARPA FastEthernet0/0.23
Internet 192.168.23.3 - c203.247c.0000 ARPA FastEthernet0/0.23
Could that be MTU related?
From: soltanian at gmail.com
To: eng_mssk at hotmail.com; cisco-nsp at puck.nether.net
Subject: RE: [c-nsp] Cisco Juniper Xconnect
Date: Sun, 24 Apr 2016 16:05:50 +0430
I did this for about 1200 Nodes and had no issue But on an actual box(M20). Anyway this may be related to GNS3 and emulation. Also we don’t use following line: set protocols l2circuit neighbor 1.1.1.1 interface em1.23 encapsulation-type ethernet-vlan
set protocols l2circuit neighbor 1.1.1.1 interface em1.23 ignore-encapsulation-mismatch
set protocols l2circuit neighbor 1.1.1.1 interface em1.23 ignore-mtu-mismatch
The first three line is enough. This also can be related to VLAN rewrite section. Do you have traffic in one direction? I mean for example do you have ARP entry from Source IP address on destination device?Getting a PCAP file is also useful. From: Mohammad Khalil [mailto:eng_mssk at hotmail.com]
Sent: Sunday, April 24, 2016 3:59 PM
To: Alireza Soltanian <soltanian at gmail.com>; cisco-nsp at puck.nether.net
Subject: RE: [c-nsp] Cisco Juniper Xconnect set protocols l2circuit neighbor 1.1.1.1 interface em1.23 virtual-circuit-id 23
set protocols l2circuit neighbor 1.1.1.1 interface em1.23 no-control-word
set protocols l2circuit neighbor 1.1.1.1 interface em1.23 mtu 1500
set protocols l2circuit neighbor 1.1.1.1 interface em1.23 encapsulation-type ethernet-vlan
set protocols l2circuit neighbor 1.1.1.1 interface em1.23 ignore-encapsulation-mismatch
set protocols l2circuit neighbor 1.1.1.1 interface em1.23 ignore-mtu-mismatch
I have added the no-control-word on Juniper and changed the xconnect on Cisco (i was already doing that , but I made the pseduwire to manipulate the parameters)
Still no luck > From: soltanian at gmail.com
> To: eng_mssk at hotmail.com; cisco-nsp at puck.nether.net
> Subject: RE: [c-nsp] Cisco Juniper Xconnect
> Date: Sun, 24 Apr 2016 15:41:17 +0430
>
> Hi
> I cannot read JunOS configuration part properly, But it seems you did not
> disable Control-word on Juniper side. Did you check this?
>
>
>
> -----Original Message-----
> From: cisco-nsp [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of
> Mohammad Khalil
> Sent: Sunday, April 24, 2016 3:22 PM
> To: cisco-nsp at puck.nether.net
> Subject: [c-nsp] Cisco Juniper Xconnect
>
> Hi all
> Am trying to simulate xconnect between Cisco and Juniper using GNS3 will it
> work in the first manner on GNS3? if so , please check my conf below
>
> R2 - R1 - J1 - R3
>
> R2
> interface FastEthernet0/0
> no ip address
> speed 100
> full-duplex
>
> interface FastEthernet0/0.23
> encapsulation dot1Q 23
> ip address 192.168.23.2 255.255.255.0
>
> R3
> interface FastEthernet0/0
> no ip address
> speed 100
> full-duplex
>
> interface FastEthernet0/0.23
> encapsulation dot1Q 23
> ip address 192.168.23.3 255.255.255.0
>
> R1
> router ospf 1
> router-id 1.1.1.1
> network 1.1.1.1 0.0.0.0 area 0
> network 192.168.101.1 0.0.0.0 area 0
>
> interface FastEthernet1/0
> ip address 192.168.101.1 255.255.255.0
> speed 100
> duplex full
> mpls ip
> mpls mtu 1514
>
> interface FastEthernet1/1
> no ip address
> speed 100
> duplex full
>
> interface FastEthernet1/1.23
> encapsulation dot1Q 23
> xconnect 10.10.10.10 23 encapsulation mpls pw-class MSSK
>
> pseudowire-class MSSK
> encapsulation mpls
> interworking vlan
> no control-word
>
> J1
> set version 12.1R1.9
> set system root-authentication encrypted-password cisco123 set system syslog
> user * any emergency set system syslog file messages any notice set system
> syslog file messages authorization info set system syslog file
> interactive-commands interactive-commands any set interfaces em0 mtu 1514
> set interfaces em0 unit 0 family inet address 192.168.101.10/24 set
> interfaces em0 unit 0 family mpls mtu 1500 set interfaces em1 vlan-tagging
> set interfaces em1 unit 23 encapsulation vlan-ccc set interfaces em1 unit 23
> vlan-id 23 set interfaces em1 unit 23 family ccc set interfaces lo0 unit 0
> family inet address 10.10.10.10/32 set protocols mpls interface em0.0 set
> protocols mpls interface lo0.0 set protocols ospf area 0.0.0.0 interface
> em0.0 set protocols ospf area 0.0.0.0 interface lo0.0 set protocols ldp
> interface em0.0 set protocols ldp interface lo0.0 set protocols l2circuit
> neighbor 1.1.1.1 interface em1.23 virtual-circuit-id 23 set protocols
> l2circuit neighbor 1.1.1.1 interface em1.23 mtu 1500 set protocols l2circuit
> neighbor 1.1.1.1 interface em1.23 encapsulation-type ethernet-vlan set
> protocols l2circuit neighbor 1.1.1.1 interface em1.23
> ignore-encapsulation-mismatch set protocols l2circuit neighbor 1.1.1.1
> interface em1.23 ignore-mtu-mismatch
>
> R1#sh xconnect all
> Legend: XC ST=Xconnect State S1=Segment1 State S2=Segment2 State
> UP=Up DN=Down AD=Admin Down IA=Inactive
> SB=Standby HS=Hot Standby RV=Recovering NH=No Hardware
>
> XC ST Segment 1 S1 Segment 2
> S2
> ------+---------------------------------+--+--------------------------------
> -+--
> UP pri ac Fa1/1.23:23(Eth VLAN) UP mpls 10.10.10.10:23
> UP
>
> R1#sh mpls l2transport vc 23 detail
> Local interface: Fa1/1.23 up, line protocol up, Eth VLAN 23 up
> Destination address: 10.10.10.10, VC ID: 23, VC status: up
> Output interface: Fa1/0, imposed label stack {299776}
> Preferred path: not configured
> Default path: active
> Next hop: 192.168.101.10
> Create time: 00:09:08, last status change time: 00:09:08
> Last label FSM state change time: 00:09:08
> Signaling protocol: LDP, peer 10.10.10.10:0 up
> Targeted Hello: 1.1.1.1(LDP Id) -> 10.10.10.10, LDP is UP
> Status TLV support (local/remote) : enabled/not supported
> LDP route watch : enabled
> Label/status state machine : established, LruRru
> Last local dataplane status rcvd: No fault
> Last BFD dataplane status rcvd: Not sent
> Last BFD peer monitor status rcvd: No fault
> Last local AC circuit status rcvd: No fault
> Last local AC circuit status sent: No fault
> Last local PW i/f circ status rcvd: No fault
> Last local LDP TLV status sent: No fault
> Last remote LDP TLV status rcvd: Not sent
> Last remote LDP ADJ status rcvd: No fault
> MPLS VC labels: local 19, remote 299776
> Group ID: local 0, remote 0
> MTU: local 1500, remote 1500
> Remote interface description:
> Remote VLAN id: 23
> Sequencing: receive disabled, send disabled
> Control Word: Off
> Dataplane:
> SSM segment/switch IDs: 4112/4109 (used), PWID: 1
> VC statistics:
> transit packet totals: receive 0, send 5
> transit byte totals: receive 0, send 410
> transit packet drops: receive 0, seq error 0, send 0
>
> R2#ping 192.168.23.3
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 192.168.23.3, timeout is 2 seconds:
> .....
> Success rate is 0 percent (0/5)
>
> Thanks
>
> BR,
> Mohammad
>
>
>
> _______________________________________________
> cisco-nsp mailing list cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
More information about the cisco-nsp
mailing list