[c-nsp] memory issue asr1002-x
caroyy
caroyy at yahoo.com
Wed Nov 22 05:23:41 EST 2017
Hi Guys,
Thanks for replying. The iosd i checked is a 64bits IOSd.
i suspect is my license issue. possible?
cisco ASR1002-X (2RU-X) processor (revision 2KP) with 3553107K/6147K bytes of memory.
32768K bytes of non-volatile configuration memory.
16777216K bytes of physical memory.
#show redundancy
Redundant System Information :
------------------------------
Available system uptime = 2 hours, 28 minutes
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Simplex
Configured Redundancy Mode = Non-redundant
Operating Redundancy Mode = Non-redundant
Maintenance Mode = Disabled
Communications = Down Reason: Failure
Current Processor Information :
-------------------------------
Active Location = slot 6
Current Software state = ACTIVE
Uptime in current state = 2 hours, 28 minutes
Image Version = Cisco IOS Software [Fuji], ASR1000 Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.7.1, RELEASE SOFTWARE (fc5)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Wed 15-Nov-17 19:34 by mcpre
BOOT = bootflash:asr1002x-universalk9.16.07.01.SPA.bin,1;
CONFIG_FILE =
Configuration register = 0x2102
Peer (slot: 7) information is not available because it is in 'DISABLED' state
Regards,caroyy
Hi,
On Wed, 22 Nov 2017, James Bensley wrote:
On 22 November 2017 at 03:32, caroyy via cisco-nsp
<cisco-nsp at puck.nether.net> wrote:
Hi David,
Thank you for replying.Ya the memory allocated 3.5gb to IOSD from the platform is unusually strange. It should be 6.5gb based on 16gb memory router.
Just asking the community if anyone has solve/encounter the same problem.Unfortunately, this router i took over from someone and there is no smartnet available.
Regards,caroyy
Hi Caroyy,
I believe that the IOSd process is a 32-bit process so it can't use
more than 4GBs of RAM.
does not look like it on this box:
Router#show version | i mem
cisco ASR1001 (1RU) processor with 6848986K/6147K bytes of memory.
32768K bytes of non-volatile configuration memory.
16777216K bytes of physical memory.
Router#
Try looking at the output of "show redundancy". The ASR1000 had some kind of IOS redundancy feature to run two IOS processes on a box splitting up memory between them.
Greetings
Christian
--
Christian Kratzer CK Software GmbH
Email: ck at cksoft.de Wildberger Weg 24/2
Phone: +49 7032 893 997 - 0 D-71126 Gaeufelden
Fax: +49 7032 893 997 - 9 HRB 245288, Amtsgericht Stuttgart
Mobile: +49 171 1947 843 Geschaeftsfuehrer: Christian Kratzer
Web: http://www.cksoft.de/
_______________________________________________
cisco-nsp mailing list cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
On Wednesday, November 22, 2017, 11:32:16 AM GMT+8, caroyy <caroyy at yahoo.com> wrote:
Hi David,
Thank you for replying.Ya the memory allocated 3.5gb to IOSD from the platform is unusually strange. It should be 6.5gb based on 16gb memory router.
Just asking the community if anyone has solve/encounter the same problem.Unfortunately, this router i took over from someone and there is no smartnet available.
Regards,caroyy
On Wednesday, November 22, 2017, 10:06:33 AM GMT+8, David Prall <dcp at dcptech.com> wrote:
This is how much memory has been assigned to iosd. Show version will display memory allocated to iosd and the total memory installed.
David
--
http://dcp.dcptech.com
On 11/21/17, 5:56 AM, "cisco-nsp on behalf of caroyy via cisco-nsp" <cisco-nsp-bounces at puck.nether.net on behalf of cisco-nsp at puck.nether.net> wrote:
_______________________________________________
cisco-nsp mailing list cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
More information about the cisco-nsp
mailing list