[c-nsp] ASR9000 HW compatibility

[Rimestad, Steinar]

Hi.

The 48x10GE is a Tomahawk based linecard using A9K-NP300-LC and thus needs V2 fan trays. These linecards also require both fantrays to be UP to boot. I had this issue when trying to install a 4x100GE LC, even though the hardware installation guide only mentions this for the 8x100GE card.
https://www.cisco.com/c/en/us/td/docs/iosxr/asr9000/hardware-install/ethernet-line-card-installation-guide/b-asr9k-ethernt-line-card-install-guide/b-asr9k-ethernt-line-card-install-guide_chapter_00.html 

You will most likely get an error message similar to this
shelfmgr[416]: %PLATFORM-SHELFMGR-3-INCOMPATIBLE_FT_FOR_LC : All the Fantrays must be V2 in order to provide cooling for the A9K-NP300-LC. Chassis has incompatible Fantray for Node 0/2/CPU0

/ Steinar 
 

On 21/11/2017, 10:53, "cisco-nsp on behalf of Ted Pelas Johansson" <cisco-nsp-bounces at puck.nether.net on behalf of ted.johansson at tele2.com> wrote:

    Sorry, misread your question.
    
    The v1 chassis nor power modules should not be a problem, but it could be an issue with the old fans.
    Do not find any good information regarding the fans, but try to reach out to your account team and they will help you out.
    
    And you need to run XR 6.2.1 or later.
    
    /Ted
    
    -----Original Message-----
    From: cisco-nsp [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Ted Pelas Johansson
    Sent: den 21 november 2017 10:43
    To: Dmitry Kiselev <dmitry at dmitry.net>; cisco-nsp at puck.nether.net
    Subject: Re: [c-nsp] ASR9000 HW compatibility
    
    [This sender failed our fraud detection checks and may not be who they appear to be. Learn about spoofing at http://aka.ms/LearnAboutSpoofing]
    
    https://www.cisco.com/c/en/us/products/collateral/routers/asr-9000-series-aggregation-services-routers/datasheet-c78-738704.html
    
    /Ted
    
    -----Original Message-----
    From: cisco-nsp [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Dmitry Kiselev
    Sent: den 21 november 2017 09:33
    To: cisco-nsp at puck.nether.net
    Subject: [c-nsp] ASR9000 HW compatibility
    
    Hi!
    
    
    Could any on the list advice me are new 48-ports 10G line cards (A9K-48x10GE) can run inside old ASR9010 v01 chassis with old v01 power modules and fans? Assuming power budget is enough and XR has already updated.
    
    I've already checked cisco and live! sites but found no any hints. :(
    
    
    Thanks in advance
    
    
    --
    
    Dmitry Kiselev
    
    _______________________________________________
    cisco-nsp mailing list  cisco-nsp at puck.nether.net
    https://puck.nether.net/mailman/listinfo/cisco-nsp
    archive at http://puck.nether.net/pipermail/cisco-nsp/
    
    ******** IMPORTANT NOTICE ********
    The content of this e-mail is intended for the addressee(s) only and may contain information that is confidential and/or otherwise protected from disclosure. If you are not the intended recipient, please note that any copying, distribution or any other use or dissemination of the information contained in this e-mail (and its attachments) is strictly prohibited. If you have received this e-mail in error, kindly notify the sender immediately by replying to this e-mail and delete the e-mail and any copies thereof.
    
    Tele2 AB (publ) and its subsidiaries (“Tele2 Group”) accepts no responsibility for the consequences of any viruses, corruption or other interference transmitted by e-mail.
    _______________________________________________
    cisco-nsp mailing list  cisco-nsp at puck.nether.net
    https://puck.nether.net/mailman/listinfo/cisco-nsp
    archive at http://puck.nether.net/pipermail/cisco-nsp/
    
    ******** IMPORTANT NOTICE ********
    The content of this e-mail is intended for the addressee(s) only and may contain information that is confidential and/or otherwise protected from disclosure. If you are not the intended recipient, please note that any copying, distribution or any other use or dissemination of the information contained in this e-mail (and its attachments) is strictly prohibited. If you have received this e-mail in error, kindly notify the sender immediately by replying to this e-mail and delete the e-mail and any copies thereof.
    
    Tele2 AB (publ) and its subsidiaries (“Tele2 Group”) accepts no responsibility for the consequences of any viruses, corruption or other interference transmitted by e-mail.
    _______________________________________________
    cisco-nsp mailing list  cisco-nsp at puck.nether.net
    https://puck.nether.net/mailman/listinfo/cisco-nsp
    archive at http://puck.nether.net/pipermail/cisco-nsp/