[c-nsp] Route Leaking (GRT<-> VRF)
CiscoNSP List
CiscoNSP_list at hotmail.com
Sun Apr 29 06:30:04 EDT 2018
Hi,
(Apologies in advance, rather long post)
Have setup a peering vrf to test route leaking (GRT<->VRF)
For the route leaking, added the following to two PEs (Both having a vrf interface on them) vrf definition:
address-family ipv4
import ipv4 unicast 10000 map RP_TEST_PREFIXES_GRT
export ipv4 unicast 10000 map RP_TEST_PEERING_PARTNERS_PREFIXES_VRF
#sh run | sec route-map RP_TEST_PREFIXES_GRT
route-map RP_TEST_PREFIXES_GRT permit 10
match community CL_GRT_TEST_PREFIXES
#sh run | include CL_GRT_TEST_PREFIXES
ip community-list standard CL_GRT_TEST_PREFIXES permit NNNNN:1301
#sh run | sec route-map RP_TEST_PEERING_PARTNERS_PREFIXES_VRF
route-map RP_TEST_PEERING_PARTNERS_PREFIXES_VRF permit 10
match community CL_TEST_PEERING_PARTNERS_PREFIXES_VRF
#sh run | include CL_TEST_PEERING_PARTNERS_PREFIXES_VRF
ip community-list standard CL_TEST_PEERING_PARTNERS_PREFIXES_VRF permit NNNNN:4000
Both PEs are able to reach VRF IPs on the remote PE (And themselves)
Both PEs are able to reach GRT IPs on themselves (From VRF), but are unable to reach "some" GRT IPs on the remote PE
(And in GRT)
I originally thought it was IGP in GRT(It carries our PEs loops) - Those Loops have RIB failure on our PEs as IGP(OSPF) is
preferred over BGP.....So I thought the RIB failure was somehow being "copied" into the VRF when route leaking occurred, and
Next Hop for remote routes wasnt reachable...but the more prefixes in Global I tested, it became clear that next hop was
"ok"...well for some destinations anyway.....The current situation is that if I test from both PEs to an IP in our GRT, some work,
some dont, some work on one PE, but not the other??
A sample of one remote IP that works on one of the PE's but not on the other....Ive been staring at this for way too long, but I
cant see anything glaringly obvious(different) between what PE_A "sees" vs PE_B....and what could eb causing one to fail to
reach the remote IP....hopefully somebody has suggestions on where to go from here.
Cheers
### PE Test for remote GRT IP that works from one PE, but not the other:
Remote IP: XXX.YYY.ZZ.186 (Loopback of another PE)
>From PE "A" with Peering VRF setup
Ping fails:
VRF:
#ping vrf TEST_PEERING XXX.YYY.ZZ.186
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to XXX.YYY.ZZ.186, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
GRT:
#ping XXX.YYY.ZZ.186
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to XXX.YYY.ZZ.186, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 24/24/28 ms
VRF BGP table:
#sh ip bgp vpnv4 vrf TEST_PEERING XXX.YYY.ZZ.186
BGP routing table entry for XXX.YYY.ZZ.130:4000:XXX.YYY.ZZ.186/32, version 1460495
BGP Bestpath: compare-routerid
Paths: (4 available, best #4, table TEST_PEERING)
Additional-path-install
Not advertised to any peer
Refresh Epoch 2
Local, (received & used), imported path from XXX.YYY.ZZ.186/32 (global)
XXX.YYY.ZZ.186 (metric 7) (via default) from XXX.YYY.ZZ.213 (XXX.YYY.ZZ.213)
Origin incomplete, metric 0, localpref 100, valid, internal, no-import, no-import
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.1
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used), imported path from XXX.YYY.ZZ.186/32 (global)
XXX.YYY.ZZ.186 (metric 7) (via default) from XXX.YYY.ZZ.212 (XXX.YYY.ZZ.212)
Origin incomplete, metric 0, localpref 100, valid, internal, no-import, no-import
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.1
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used), imported path from XXX.YYY.ZZ.186/32 (global)
XXX.YYY.ZZ.186 (metric 7) (via default) from XXX.YYY.ZZ.205 (XXX.YYY.ZZ.205)
Origin incomplete, metric 0, localpref 100, valid, internal, no-import, no-import
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.2
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used), imported path from XXX.YYY.ZZ.186/32 (global)
XXX.YYY.ZZ.186 (metric 7) (via default) from XXX.YYY.ZZ.204 (XXX.YYY.ZZ.204)
Origin incomplete, metric 0, localpref 100, valid, internal, no-import, no-import, best
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.2
rx pathid: 0, tx pathid: 0x0
GRT BGP:
#sh ip bgp XXX.YYY.ZZ.186
BGP routing table entry for XXX.YYY.ZZ.186/32, version 493438
BGP Bestpath: compare-routerid
Paths: (4 available, best #1, table default, RIB-failure(17))
Additional-path-install
Not advertised to any peer
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.186 (metric 7) from XXX.YYY.ZZ.204 (XXX.YYY.ZZ.204)
Origin incomplete, metric 0, localpref 100, valid, internal, af-export(1), best
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.2
rx pathid: 0, tx pathid: 0x0
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.186 (metric 7) from XXX.YYY.ZZ.205 (XXX.YYY.ZZ.205)
Origin incomplete, metric 0, localpref 100, valid, internal, af-export(1)
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.2
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.186 (metric 7) from XXX.YYY.ZZ.212 (XXX.YYY.ZZ.212)
Origin incomplete, metric 0, localpref 100, valid, internal, af-export(1)
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.1
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.186 (metric 7) from XXX.YYY.ZZ.213 (XXX.YYY.ZZ.213)
Origin incomplete, metric 0, localpref 100, valid, internal, af-export(1)
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.1
rx pathid: 0, tx pathid: 0
# Reverse Direction: (VRF not setup on this PE)
PE03-MEL-ME1_RME1_01_10245_1717-RU27#ping XXX.YYY.ZZ.130
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to XXX.YYY.ZZ.130, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 24/24/24 ms
#sh ip bgp XXX.YYY.ZZ.130
BGP routing table entry for XXX.YYY.ZZ.130/32, version 79885314
BGP Bestpath: compare-routerid
Paths: (4 available, best #1, table default, RIB-failure(17))
Additional-path-install
Flag: 0x20
Not advertised to any peer
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.130 (metric 7) from XXX.YYY.ZZ.204 (XXX.YYY.ZZ.204)
Origin incomplete, metric 0, localpref 100, valid, internal, best
Community: NNNNN:1000 NNNNN:1301 NNNNN:15000
Originator: XXX.YYY.ZZ.130, Cluster list: 0.0.0.2
rx pathid: 0, tx pathid: 0x0
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.130 (metric 7) from XXX.YYY.ZZ.205 (XXX.YYY.ZZ.205)
Origin incomplete, metric 0, localpref 100, valid, internal
Community: NNNNN:1000 NNNNN:1301 NNNNN:15000
Originator: XXX.YYY.ZZ.130, Cluster list: 0.0.0.2
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.130 (metric 7) from XXX.YYY.ZZ.212 (XXX.YYY.ZZ.212)
Origin incomplete, metric 0, localpref 100, valid, internal
Community: NNNNN:1000 NNNNN:1301 NNNNN:15000
Originator: XXX.YYY.ZZ.130, Cluster list: 0.0.0.1
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.130 (metric 7) from XXX.YYY.ZZ.213 (XXX.YYY.ZZ.213)
Origin incomplete, metric 0, localpref 100, valid, internal
Community: NNNNN:1000 NNNNN:1301 NNNNN:15000
Originator: XXX.YYY.ZZ.130, Cluster list: 0.0.0.1
rx pathid: 0, tx pathid: 0
PE03-MEL-ME1_RME1_01_10245_1717-RU27#
# And then from the other PE with VRF defined:
Ping success:
#ping vrf TEST_PEERING XXX.YYY.ZZ.186
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to XXX.YYY.ZZ.186, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 26/30/45 ms
Global success:
#ping XXX.YYY.ZZ.186
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to XXX.YYY.ZZ.186, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 29/29/29 ms
VRF BGP
#sh ip bgp vpnv4 vrf TEST_PEERING XXX.YYY.ZZ.186
BGP routing table entry for XXX.YYY.ZZ.201:4000:XXX.YYY.ZZ.186/32, version 5108833
BGP Bestpath: compare-routerid
Paths: (4 available, best #4, table TEST_PEERING)
Additional-path-install
Not advertised to any peer
Refresh Epoch 2
Local, (received & used), imported path from XXX.YYY.ZZ.186/32 (global)
XXX.YYY.ZZ.186 (metric 9) (via default) from XXX.YYY.ZZ.213 (XXX.YYY.ZZ.213)
Origin incomplete, metric 0, localpref 100, valid, internal, no-import, no-import
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.1
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used), imported path from XXX.YYY.ZZ.186/32 (global)
XXX.YYY.ZZ.186 (metric 9) (via default) from XXX.YYY.ZZ.212 (XXX.YYY.ZZ.212)
Origin incomplete, metric 0, localpref 100, valid, internal, no-import, no-import
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.1
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used), imported path from XXX.YYY.ZZ.186/32 (global)
XXX.YYY.ZZ.186 (metric 9) (via default) from XXX.YYY.ZZ.205 (XXX.YYY.ZZ.205)
Origin incomplete, metric 0, localpref 100, valid, internal, no-import, no-import
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.2
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used), imported path from XXX.YYY.ZZ.186/32 (global)
XXX.YYY.ZZ.186 (metric 9) (via default) from XXX.YYY.ZZ.204 (XXX.YYY.ZZ.204)
Origin incomplete, metric 0, localpref 100, valid, internal, no-import, no-import, best
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.2
rx pathid: 0, tx pathid: 0x0
Global BGP:
#sh ip bgp XXX.YYY.ZZ.186
BGP routing table entry for XXX.YYY.ZZ.186/32, version 82276054
BGP Bestpath: compare-routerid
Paths: (4 available, best #1, table default, RIB-failure(17))
Additional-path-install
Not advertised to any peer
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.186 (metric 9) from XXX.YYY.ZZ.204 (XXX.YYY.ZZ.204)
Origin incomplete, metric 0, localpref 100, valid, internal, af-export(1), best
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.2
rx pathid: 0, tx pathid: 0x0
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.186 (metric 9) from XXX.YYY.ZZ.205 (XXX.YYY.ZZ.205)
Origin incomplete, metric 0, localpref 100, valid, internal, af-export(1)
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.2
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.186 (metric 9) from XXX.YYY.ZZ.212 (XXX.YYY.ZZ.212)
Origin incomplete, metric 0, localpref 100, valid, internal, af-export(1)
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.1
rx pathid: 0, tx pathid: 0
Refresh Epoch 2
Local, (received & used)
XXX.YYY.ZZ.186 (metric 9) from XXX.YYY.ZZ.213 (XXX.YYY.ZZ.213)
Origin incomplete, metric 0, localpref 100, valid, internal, af-export(1)
Community: NNNNN:1000 NNNNN:1301 NNNNN:12000
Originator: XXX.YYY.ZZ.186, Cluster list: 0.0.0.1
rx pathid: 0, tx pathid: 0
More information about the cisco-nsp
mailing list