[cisco-voip] 7200 VXB-2TE1 h323 gateway...

[Wes Sisk]

Oh, and then for the rest of the setup,
add the gateway to 2 different route groups with different
stip/prefix digits.  Then point the Pattern->List to the appropriate group.

/wes

> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net]On Behalf Of Wes Sisk
> Sent: Monday, July 14, 2003 4:46 PM
> To: Jeff Behl
> Cc: cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] 7200 VXB-2TE1 h323 gateway...
>
>
> Nope.
>
> To be able to route specific calls to different ports you will
> either need to get a bit creative with your dialplan.
>
> Currently you probably have dial-peers with something like 9.T
> going out both ports.  Change this so 7.T goes out one port and 9.T goes
> out the other port.  Then use the Route Pattern/Route List/Route Group
> in /CCMAdmin to strip/prepend the appropriate trunk access code.
>
> /Wes
>
> > -----Original Message-----
> > From: Jeff Behl [mailto:jeff at expertcity.com]
> > Sent: Monday, July 14, 2003 4:40 PM
> > To: Wes Sisk
> > Cc: cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] 7200 VXB-2TE1 h323 gateway...
> >
> >
> > thanks.  one q remaining:  once I do this will i have the ability to
> > add individual ports on the adaptor (there are two) to different route
> > groups?
> >
> >
> > thanks again.
> > jeff
> >
> > Wes Sisk wrote:
> >
> > > Sounds like you have your route pattern directly at the gateway
> > > so the gateway is not eligible to be in a routegroup.
> > > To get around it consider something like this:
> > >
> > > change your route patter to point at a route list
> > > (this frees the gateway to be added to a route group)
> > >
> > > Then configure your gateway to be in the route groups you desire.
> > >
> > > /Wes
> > >
> > >
> > >>-----Original Message-----
> > >>From: cisco-voip-bounces at puck.nether.net
> > >>[mailto:cisco-voip-bounces at puck.nether.net]On Behalf Of Jeff Behl
> > >>Sent: Monday, July 14, 2003 1:25 PM
> > >>To: cisco-voip at puck.nether.net
> > >>Subject: [cisco-voip] 7200 VXB-2TE1 h323 gateway...
> > >>
> > >>
> > >>i have a 7200 with the above which is currently registered to the cm.
> > >>what i'd like to do is put each pri port into its own route
> group then
> > >>create a route list of the two groups.  is this possible in this
> > >>situation?  right now putting the gateway by itself into a
> route group
> > >>isn't possible as it doesn't show up as a possible addtion when
> > creating
> > >>one, though I've heard that it won't show up if the gateway
> is already
> > >>defined for use in a dial pattern...
> > >>
> > >>thanks
> > >>
> > >>_______________________________________________
> > >>cisco-voip mailing list
> > >>cisco-voip at puck.nether.net
> > >>http://puck.nether.net/mailman/listinfo/cisco-voip
> >
> >
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> http://puck.nether.net/mailman/listinfo/cisco-voip