[cisco-voip] RE: [PACUG] Route Pattern / Translation pattern / MGCP

[Wes Sisk]

nope, MGCP gw cannot translate the number before passing back to CCM
(AFAIK).
Sounds like the 0 to operator will have to become extension "0" on a dummy
phone with CFA configured.
This will remove the urgent priority, but you will have to wait for
interdigit
timeout anytime you attempt to dial operator at "0" becuase we don't know if
you mean "0" or "0159".

/Wes

> -----Original Message-----
> From: Voll, Scott [mailto:Scott.Voll at wesd.org]
> Sent: Thursday, October 16, 2003 2:17 PM
> To: Wes Sisk; Portland Area Cisco Users Group;
> cisco-voip at puck.nether.net; pacug at patch.com
> Subject: RE: [cisco-voip] RE: [PACUG] Route Pattern / Translation
> pattern / MGCP
>
>
> So how do I remove the overlap?  The phone number is 503-472-0512.  CM /
> MGCP Router strips it down to 0512.  It used to be a POTS line and now
> is being routed down the PRI to the new ext. 5920. Can the MGCP Router
> change it before it gets to CM?
>
> Scott
>
> -----Original Message-----
> From: Wes Sisk [mailto:wsisk at cisco.com]
> Sent: Thursday, October 16, 2003 11:10 AM
> To: Portland Area Cisco Users Group; cisco-voip at puck.nether.net;
> pacug at patch.com
> Subject: [cisco-voip] RE: [PACUG] Route Pattern / Translation pattern /
> MGCP
>
> Scott,
>
> have 0 for operator and 0512 creates an overlapping dialplan.
>
> when you setup the operator 0 translation pattern that is marked
> for "urgent priority" by default which means anytime ccm receives
> the digit string "0" it will match this pattern and immediately route
> the
> call.
>
> Under route patterns you have the option of enable/disable urgent
> priorty.
>
> There really is no clean solution when using overlapping dialplan.
> Your best bet is to remove the overlap.
>
> /Wes
>
>
> > -----Original Message-----
> > From: pacug-bounces at tire.patch.com
> > [mailto:pacug-bounces at tire.patch.com]On Behalf Of Voll, Scott
> > Sent: Thursday, October 16, 2003 1:57 PM
> > To: cisco-voip at puck.nether.net; pacug at patch.com
> > Subject: [PACUG] Route Pattern / Translation pattern / MGCP
> >
> >
> >
> > I have CM 3.3.3 and a 3640 running MGCP 12.2.15T.
> >
> > I have set up a translation pattern of 0 to translate to the
> > Receptionist x5900.
> >
> > Here's my problem.
> >
> > I now have to route some old numbers into this new system.  The number
> > just happens to be 0512.
> >
> > So if I test it I go to the receptionist.  How do I make it so that
> when
> > the number comes in on my PRI it goes to the fax machine x5920 like it
> > should.  Translation pattern already set up.
> >
> > Is there some kind of time out I need to set on the Router, CM?
> >
> > Help Please,
> >
> > Scott Voll
> > Network Analyst, CCNA
> > Willamette ESD
> >
> > _______________________________________________
> > PACUG mailing list
> > PACUG at tire.patch.com
> > http://tire.patch.com/mailman/listinfo/pacug
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip