[cisco-voip] VoIP to VoIP calls

[Steven E. Ames]

Just the following:

Configuring multi-service IP-to-IP Gateways
http://www.cisco.com/en/US/products/sw/voicesw/ps5640/products_configuration_guide_chapter09186a00801e7e50.html

configureing Enhanced Conferencing and Transcoding for Voice Gateway Routers (CCM)
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgcr/vvfax_c/callc_c/ccm_c/intcnf2.htm

Cisco Multi-service Ip-to-IP gateways
http://www.cisco.com/en/US/products/sw/voicesw/ps5640/products_configuration_guide_chapter09186a00801d0826.html


-Steve

> -----Original Message-----
> From: kostas anagnopoulos [mailto:kostas.anagnopoulos at oteglobe.net]
> Sent: Thursday, December 09, 2004 10:00 PM
> To: Steven E. Ames
> Cc: shafiim at global-telecom.com; cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] VoIP to VoIP calls
> 
> 
> Hi,
> 
> Do you have any sample config regarding transcoding in 
> ip-to-ip gw.I cannot
> find anything relevant on cco.
> 
> thanks,
> Kostas
> 
> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net]On Behalf Of Steven E. Ames
> Sent: Friday, December 10, 2004 4:11 PM
> To: shafiim at global-telecom.com; cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] VoIP to VoIP calls
> 
> 
> This has been sorta possible with H.323 to H.323 legs for a 
> while. A recent
> release 12.3.11(T) allows SIP<->H.323. The key is here:
> 
> voice service voip
>  allow-connections sip to h323
> 
> Would allow an incoming SIP call to match to an outgoing 
> H.323 dial-peer.
> Codec transcoding is also possible (but only g.711/g.729).
> 
> -Steve
> 
> > -----Original Message-----
> > From: cisco-voip-bounces at puck.nether.net
> > [mailto:cisco-voip-bounces at puck.nether.net]On Behalf Of
> > Shafii MOHAMMED
> > Sent: Friday, December 10, 2004 6:48 AM
> > To: cisco-voip at puck.nether.net
> > Subject: [cisco-voip] VoIP to VoIP calls
> >
> >
> > Hi,
> > I was wondering if voice enabled routers like 2600, 3600, or
> > 5300 support
> > voip to voip dial-peers.
> >
> > I have defined two dial-peers on my 2651XM like this:
> >
> > !
> > dial-peer voice 1 voip
> >  destination-pattern .T
> >  session target ipv4:10.1.1.1
> > !
> > dial-peer voice 2 voip
> >  destination-pattern 1000
> >  session target ipv4:10.1.1.2
> > !
> >
> > I am trying to let my 2651XM route a call from one voip dial
> > leg to another
> > voip dial leg, is this possible?
> >
> > Thanks,
> > Shafii
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> 
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
> 
> --
> This message has been scanned for viruses and
> dangerous content by MailScanner, and is
> believed to be clean.
> 
> 
> 
> 
> -- 
> This message has been scanned for viruses and
> dangerous content by MailScanner, and is
> believed to be clean.
> 
>