[cisco-voip] Adding Dial Peer

[Wes Sisk]

Just a thought - have all calls routed to the CM first, and if the CM 
does not find an exact match, have a wildcard route pattern that sends 
the call back to the router with a prefix so the router can match a pots 
peer and handoff to the PBX.

Tandem over h323 doesn't tie up any real physical trunks and the CM can 
do that all day long.

/Wes

Voll, Scott wrote:

>Unfortunately I'm in the middle of a long painful process of moving from
>a PBX with about 500 DID's to VoIP.  And the best part is that we are
>moving department by department.  As each department has the money to by
>phones I move them over.  Since I started this last year I have about
>150 of the 500 moved over.  Most DID are in the middle of the range of
>the DID Block.
>
>This means for redundancies purposes, I have two dial-peers per IP phone
>on my H323 GW, one for the pub and one for the sub.
>
>I did look at memory and it looks like I have about 2mb left.  The good
>think is I'm moving to my CMM 6PRI next week.  And I'm hoping to move to
>MGCP rather then h323.  At the time Cisco and my PBX didn't call process
>nicely.  But cisco now supports more with there MGCP now.
>
>Thanks to everyone for the memory info.
>
>Scott
>
>-----Original Message-----
>From: cisco-voip-bounces at puck.nether.net
>[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of chris donnelly
>Sent: Friday, October 15, 2004 7:19 AM
>To: cisco-voip at puck.nether.net
>Subject: RE: [cisco-voip] Adding Dial Peer
>
>Yep, I agree - either memory or dial peer already exists....
>
>That's a hell of a lot of dial-peers....
>
>-----Original Message-----
>From: Walenta, Phil [mailto:philip.walenta at berbee.com] 
>Sent: 15 October 2004 15:16
>To: Voll, Scott; cisco-voip at puck.nether.net
>Subject: RE: [cisco-voip] Adding Dial Peer
>
>The last time I remember seeing this message, it was due to the router
>being out of memory.  It's a good bet, that with 103 dial peers, that's
>what you're running into.
>
>________________________________
>
>From: cisco-voip-bounces at puck.nether.net on behalf of Voll, Scott
>Sent: Fri 10/15/2004 9:05 AM
>To: cisco-voip at puck.nether.net
>Subject: [cisco-voip] Adding Dial Peer
>
>
>
>Has anyone else seen this problem?
>
>PBX-VoIP(config)#dial-peer voice 10 pots
>ERROR: could not add peer
>
>When I try to add a dail peer I get error above.  I currently am using a
>2621 running Ver. 12.3(10).
>
>Is there a max dial peer?  I currently only have 103 dial peers.
>
>Any ideas?
>
>Scott
>
>
>_______________________________________________
>cisco-voip mailing list
>cisco-voip at puck.nether.net
>https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
>_______________________________________________
>cisco-voip mailing list
>cisco-voip at puck.nether.net
>https://puck.nether.net/mailman/listinfo/cisco-voip
>
>_____________________________________________________________________
>This message has been checked for all known viruses by the MessageLabs
>Virus Control Centre.
>
>
>_______________________________________________
>cisco-voip mailing list
>cisco-voip at puck.nether.net
>https://puck.nether.net/mailman/listinfo/cisco-voip
>
>_______________________________________________
>cisco-voip mailing list
>cisco-voip at puck.nether.net
>https://puck.nether.net/mailman/listinfo/cisco-voip
>  
>