[cisco-voip] CM and Unity Upgrade Questions

[Kevin Thorngren]

Hi Lelio,

Yes, you could go through the procedure you stated.  You would be back  
to where you started though.  Keep in mind that the CCM Engineering  
Specials are cumulative, unlike Unity.  ES09 contains all the fixes  
starting from ES01 through ES08 and of course the fixes that go into  
ES09.

HTH,
Kevin

On Aug 15, 2005, at 10:32 PM, Lelio Fulgenzi wrote:

> I assumed (perhaps incorrectly) that you could apply an ES patch after  
> an SR and be back to where you were. If one were using ES09 and  
> uninstalled it to install SR1 could they not just apply ES09 again  
> after the SR1?
>  
>> ----- Original Message -----
>> From: Kevin Thorngren
>> To: Lelio Fulgenzi
>> Cc: cisco-voip at puck.nether.net
>> Sent: Monday, August 15, 2005 9:46 PM
>> Subject: Re: [cisco-voip] CM and Unity Upgrade Questions
>>
>> I would guess that you have 4.1(3)es09 for a specific fix. If you  
>> uninstall es09 to install sr1 you will loose this fix.
>>
>> I don''t think the question regarding Unity was answered. Basically  
>> you can apply MS Hotfixes at any time but need to wait for Cisco to  
>> certify MS Service Releases. For more info please see this URL:
>> http://www.cisco.com/univercd/cc/td/doc/product/voice/c_unity/ 
>> cmptblty/msupdate.htm#wp74388
>>
>> Kevin
>> On Aug 15, 2005, at 8:37 PM, Lelio Fulgenzi wrote:
>>
>>>
>>> From the release notes, this is where I got my confusion.
>>>  
>>> Under "Version and Description" it says:
>>> Note:     If you are running Cisco CallManager 4.1(3)ES06 or higher,  
>>> you must  uninstall the Engineering Special (ES) before you can  
>>> install this Service Release.  (You may lose fixes that were added  
>>> after ES06 and not included in the SR.)
>>>
>>> and under "Important Notes, Recommendations" it says:
>>>
>>> Make sure that you are using the correct version of Cisco  
>>> CallManager software.  Cisco supports upgrades from any Cisco  
>>> CallManager 4.1(3) release up to 4.1(3)ES06. This SR is based on  
>>> Engineering Special 06.
>>>  
>>> ----- Original Message -----
>>>> From: Tech Guy
>>>> To: cisco-voip at puck.nether.net
>>>> Sent: Monday, August 15, 2005 8:27 PM
>>>> Subject: Re: [cisco-voip] CM and Unity Upgrade Questions
>>>>
>>>> I read that in the docs about SR1 being based on ES06, however I did
>>>> not see anything about uninstalling anything higher.  I was actually
>>>> confused about what I should do since I have ES09, and wondered if  
>>>> the
>>>> things that ES09 fixed for us are included in SR1 seeing how it is
>>>> based off of es06 ?
>>>>
>>>> The other question then becomes do you really have to uninstall es09
>>>> in order to install SR1 ?  I was going to confirm that with TAC
>>>> myself.
>>>>
>>>> Regards,
>>>> Dane
>>>>
>>>>
>>>> On 8/15/05, Lelio Fulgenzi <lelio at uoguelph.ca> wrote:
>>>> > According to the docs, SR1 is based on ES06 and you are required  
>>>> to
>>>> > uninstall any ES greater than or equal to ES06 before applying  
>>>> the SR. The
>>>> > document is misleading, but I cleared it up with the TAC - ES06  
>>>> must be
>>>> > removed.
>>>> > 
>>>> > That being said, the Cisco folk on the list will correct me if  
>>>> that's wrong.
>>>> > 
>>>> > ----- Original Message -----
>>>> > From: Tech Guy
>>>> > To: cisco-voip at puck.nether.net
>>>> > Sent: Monday, August 15, 2005 5:01 PM
>>>> > Subject: [cisco-voip] CM and Unity Upgrade Questions
>>>> >
>>>> > I went today to get the new patches to fix the issues related to  
>>>> this
>>>> > new worm, for CallManager I went to:
>>>> >
>>>> > http://www.cisco.com/cgi-bin/tablebuild.pl/cmva-3des
>>>> >
>>>> > >From here I found the hotfixes for CallManager.
>>>> >
>>>> > After I got these however it dawned on me that these were for
>>>> > CallManager, and so I started looking around for the same  
>>>> hotfixes for
>>>> > Unity.  I can't seem to find them though.  Anyone have any ideas  
>>>> on
>>>> > where to get the same patches (if they are different) for Unity
>>>> > servers?
>>>> >
>>>> > Also, we are currently running CallManager 4.1(3)es09, I upgrade  
>>>> to
>>>> > this from CM 3.3(2) I think in April I believe, and now I notice  
>>>> there
>>>> > is a 4.1(3) SR1.
>>>> >
>>>> > I assume SR1 contains everything in es09, plus anything that was  
>>>> fixed
>>>> > between it and SR1.
>>>> >
>>>> > To upgrade to SR1 from 4.1(3)es09, do you have to order another
>>>> > upgrade kit?  I dont see anyplace to download on CCO, so I am  
>>>> assuming
>>>> > you have to do that.
>>>> >
>>>> > Thanks in advance!
>>>>
>>>> _______________________________________________
>>>> cisco-voip mailing list
>>>> cisco-voip at puck.nether.net
>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>> _______________________________________________
>>> cisco-voip mailing list
>>> cisco-voip at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-voip
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: text/enriched
Size: 5805 bytes
Desc: not available
Url : https://puck.nether.net/pipermail/cisco-voip/attachments/20050816/e854505f/attachment.bin