[cisco-voip] FXO/FXS on a single card

[Davis, Michael]

It won't work for MGCP gateways, only H.323.  You would create an inbound dial-peer that executes the TCL application.  The application askes the caller for the extension desired.  Then, an outbound leg to that extension (residing on CCM) is established.
 
Ok. Other possibilities - send those calls to a Unity directory handler, Cisco AutoAttendant (link below)  or perhaps IPCC Express.
 
http://www.cisco.com/en/US/partner/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00801ed106.html
 
 

	-----Original Message----- 
	From: IT [mailto:it at cimgroup.com] 
	Sent: Mon 12/5/2005 7:53 PM 
	To: Davis, Michael; IT; cisco-voip at puck.nether.net 
	Cc: 
	Subject: RE: [cisco-voip] FXO/FXS on a single card
	
	

	It is an MGCP gateway. How would the FXO-M1 hitting an AutoAttendant TCL
	work?
	Thanks,
	Avidan
	
	
	-----Original Message-----
	From: Davis, Michael [mailto:Michael_Davis at eLoyalty.com]
	Sent: Monday, December 05, 2005 11:57 AM
	To: IT; cisco-voip at puck.nether.net
	Subject: RE: [cisco-voip] FXO/FXS on a single card
	
	Caller-id, though supported on FXO cards with "M1" vintage, won't help
	you here. You need the card to see DNIS for direct-inward-dial support.
	Is this an MGCP or H323 gateway? Off the top of my head, you have a
	couple of possibilities.  1) Fractional T1 2) FXO-M1  that hits an
	AutoAttendant TCL script on the gateway. 
	
	
	
	
	
	
	
	        -----Original Message-----
	        From: cisco-voip-bounces at puck.nether.net on behalf of IT
	        Sent: Mon 12/5/2005 1:17 PM
	        To: cisco-voip at puck.nether.net
	        Cc:
	        Subject: [cisco-voip] FXO/FXS on a single card
	       
	       
	
	        Hi,
	       
	        I have a CallManager 4.0 installation at my headquarters office,
	and I
	        have a branch office with a 2801 connected to HQ with a point to
	point
	        T1. Currently, we have filled all 4 slots on the 2801.
	        T1- for point to point connectivity
	        FXO- for outbound 911 calling (we do not have a E911 server)
	9-port POE
	        switch- for all devices (which takes up two slots)
	       
	        This has worked well, as have been call forwarding all their
	local
	        numbers to our Headquarters PRI.  Since they are in a different
	area
	        code, this has been quite expensive. We don't want to install a
	PRI on
	        the 2801, since it seems like to much of an expense for only 6
	people. I
	        think the solution is to have an FXS and FXO in this 2801.  But,
	here
	        are my questions:
	        * I have been told an FXS card cannot handle caller-id, is this
	true?
	        * Is there an FXO/FXS on a single card, since I have run out of
	room on
	        my 2801 chassis?
	        * How many lines would an office of 6 people require?
	        * Does anyone have any other ideas?
	       
	        Thanks,
	        Avidan
	       
	        ******************************************************
	        This email may contain trade secrets and/or other information
	that is
	        proprietary and/or confidential. Use of this by anyone other
	than the
	        intended recipient(s) is prohibited and may be unlawful. If you
	are not
	        the intended recipient, delete the e-mail and notify us
	immediately.
	        ******************************************************
	       
	       
	        _______________________________________________
	        cisco-voip mailing list
	        cisco-voip at puck.nether.net
	        https://puck.nether.net/mailman/listinfo/cisco-voip