[cisco-voip] Question on PRI Gateway
Ryan Ratliff
rratliff at cisco.com
Mon Jun 20 13:46:48 EDT 2005
You will need to completely remove the pri-group command before adding
service mgcp.
Another thing you can enable is ccm-manager config. This will let CM
configure your PRI for you.
-Ryan
On Jun 20, 2005, at 1:39 PM, Anthony Mendoza wrote:
dial-peer voice 1 pots
application mgcpapp
port 1/0:23
I added the above, but still get:
rwc-faxgw-149-59(config-if)#isdn bind-l3 ?
q931 Select IOS Q.931
I also verified service mgcp:
rwc-faxgw-149-59(config)#controller T1 1/0
rwc-faxgw-(config-controller)#shut
rwc-faxgw-(config-controller)#pri-group timeslots 1-24 service mgcp
rwc-faxgw-(config-controller)#no shut
rwc-faxgw-(config-controller)#
Jun 20 10:32:50.487 PDT: %CONTROLLER-5-UPDOWN: Controller T1 1/0,
changed state t
o administratively down
Jun 20 10:32:50.743 PDT: %CONTROLLER-5-UPDOWN: Controller T1 1/0,
changed state t
o up
Jun 20 10:32:50.995 PDT: %CONTROLLER-5-UPDOWN: Controller T1 1/0,
changed state t
o down (LOF detected)
Jun 20 10:32:56.035 PDT: %CONTROLLER-5-UPDOWN: Controller T1 1/0,
changed state t
o up
rwc-faxgw-(config-controller)#end
rwc-faxgw-149-59#
What else am I missing? I actually copied my base config from a 2651
gateway of ours so I don't know why it isn't working :(
Also not sure why the service mgcp doesn't stick to the pri-group config
on the controller.
-Anthony
-----Original Message-----
From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Anthony Mendoza
Sent: Monday, June 20, 2005 7:48 AM
To: rratliff at cisco.com
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Question on PRI Gateway
I think the pots dialper is the missing one.
--------------------------
Anthony Mendoza
Senior Infrastructure Manager
t: 650-298-5955
c: 510-579-1909
f: 208-247-5501
e: amendoza at niku.com
-----Original Message-----
From: Ryan Ratliff <rratliff at cisco.com>
To: Anthony Mendoza <amendoza at Niku.com>
CC: Cisco VoIP <cisco-voip at puck.nether.net>
Sent: Mon Jun 20 07:47:38 2005
Subject: Re: [cisco-voip] Question on PRI Gateway
Your pri-group should end in 'service mgcp'
If you can't bind l3 to ccm-manager then I *think* you need a pots
dial-peer with 'port 1/0:23' and 'application MGCPAPP'.
-Ryan
On Jun 20, 2005, at 10:38 AM, Anthony Mendoza wrote:
I thought that too, but don't have that option :( Any ideas with the
below info?
rwc-faxgw-149-59(config-if)#isdn bind-l3 ?
q931 Select IOS Q.931
Here's some relevant config:
ccm-manager redundant-host 10.150.4.12 10.150.0.13 ccm-manager mgcp
ccm-manager music-on-hold !
!
controller T1 1/0
framing esf
linecode b8zs
pri-group timeslots 1-24
interface Serial1/0:23
no ip address
no logging event link-status
loopback local
isdn switch-type primary-dms100
isdn incoming-voice voice
no cdp enable
voice-port 1/0:23
!
mgcp
mgcp call-agent 10.150.4.11 service-type mgcp version 0.1 mgcp
dtmf-relay voip codec all mode out-of-band mgcp rtp unreachable timeout
1000 action notify mgcp package-capability rtp-package mgcp
package-capability sst-package no mgcp package-capability fxr-package no
mgcp timer receive-rtcp mgcp sdp simple mgcp fax t38 inhibit mgcp rtp
payload-type g726r16 static
rwc-faxgw-149-59#sho ver
Cisco Internetwork Operating System Software IOS (tm) 3600 Software
(C3640-IS-M), Version 12.3(13), RELEASE SOFTWARE
(fc2)
Technical Support: http://www.cisco.com/techsupport Copyright (c)
1986-2005 by cisco Systems, Inc.
Compiled Thu 10-Feb-05 04:28 by ssearch
Image text-base: 0x60008B00, data-base: 0x61BE6000
ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)
ROM: 3600 Software (C3640-IS-M), Version 12.3(13), RELEASE SOFTWARE
(fc2)
rwc-faxgw-149-59 uptime is 18 hours, 58 minutes System returned to ROM
by reload at 12:37:26 PDT Sun Jun 19 2005 System restarted at 12:38:56
PDT Sun Jun 19 2005 System image file is "flash:c3640-is-mz.123-13.bin"
cisco 3640 (R4700) processor (revision 0x00) with 92160K/6144K bytes of
memory.
Processor board ID 24397072
R4700 CPU at 100MHz, Implementation 33, Rev 1.0 Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Primary Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
24 Serial network interface(s)
1 Channelized T1/PRI port(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x1921
-Anthony
> -----Original Message-----
> From: Ryan Ratliff [mailto:rratliff at cisco.com]
> Sent: Monday, June 20, 2005 7:31 AM
> To: Anthony Mendoza
> Cc: Tim Frazee; Cisco VoIP
> Subject: Re: [cisco-voip] Question on PRI Gateway
>
> Make sure you have the 'isdn bind-l3 ccm-manager' command on your
> Serial interface for the PRI. I'd guess right now that MGCP isn't
> trying to backhaul your PRI.
>
> -Ryan
> On Jun 20, 2005, at 10:20 AM, Anthony Mendoza wrote:
>
> I plugged in the loop back and the interface looks up, but still not
> registering:
>
> Interface IHQ IQD OHQ OQD RXBS RXPS
> TXBS TXPS TRTL
> --------------------------------------------------------------
> ----------
> * FastEthernet0/0 0 0 0 0 11000 21
> 1000 2 0
> Serial1/0:0 0 0 0 0 0 0
> 0 0 0
> Serial1/0:1 0 0 0 0 0 0
> 0 0 0
> Serial1/0:2 0 0 0 0 0 0
> 0 0 0
> Serial1/0:3 0 0 0 0 0 0
> 0 0 0
> Serial1/0:4 0 0 0 0 0 0
> 0 0 0
> Serial1/0:5 0 0 0 0 0 0
> 0 0 0
> Serial1/0:6 0 0 0 0 0 0
> 0 0 0
> Serial1/0:7 0 0 0 0 0 0
> 0 0 0
> Serial1/0:8 0 0 0 0 0 0
> 0 0 0
> Serial1/0:9 0 0 0 0 0 0
> 0 0 0
> Serial1/0:10 0 0 0 0 0 0
> 0 0 0
> Serial1/0:11 0 0 0 0 0 0
> 0 0 0
>
> Interface IHQ IQD OHQ OQD RXBS RXPS
> TXBS TXPS TRTL
> --------------------------------------------------------------
> ----------
> Serial1/0:12 0 0 0 0 0 0
> 0 0 0
> Serial1/0:13 0 0 0 0 0 0
> 0 0 0
> Serial1/0:14 0 0 0 0 0 0
> 0 0 0
> Serial1/0:15 0 0 0 0 0 0
> 0 0 0
> Serial1/0:16 0 0 0 0 0 0
> 0 0 0
> Serial1/0:17 0 0 0 0 0 0
> 0 0 0
> Serial1/0:18 0 0 0 0 0 0
> 0 0 0
> Serial1/0:19 0 0 0 0 0 0
> 0 0 0
> Serial1/0:20 0 0 0 0 0 0
> 0 0 0
> Serial1/0:21 0 0 0 0 0 0
> 0 0 0
> Serial1/0:22 0 0 0 0 0 0
> 0 0 0
> * Serial1/0:23 0 0 0 0 0 0
> 0 0 0
>
> rwc-faxgw-149-59#sho mgcp endpoint
>
> Interface T1 1/0
>
> ENDPOINT-NAME V-PORT SIG-TYPE ADMIN
>
>
> rwc-faxgw-149-59#
>
> Any ideas for me?
>
> Thanks,
> -Anthony
>
>> -----Original Message-----
>> From: Anthony Mendoza
>> Sent: Sunday, June 19, 2005 7:17 PM
>> To: Tim Frazee; Cisco VoIP
>> Subject: RE: [cisco-voip] Question on PRI Gateway
>>
>> Thanks! I'll get my loopback plugged in tomorrow!
>>
>>
>> -Anthony
>> -----Original Message-----
>> From: Tim Frazee [mailto:tfrazee at aosgs.com]
>> Sent: Sunday, June 19, 2005 4:27 PM
>> To: Anthony Mendoza; Cisco VoIP
>> Subject: RE: [cisco-voip] Question on PRI Gateway
>>
>> You will need at least layer 2 to register.
>>
>> I normally plug in a loopback plug for staging.
>>
>>
>>
>> Timothy Frazee
>> Enterprise Engineer
>> AOS Global Solutions
>>
>> Cisco IP Phone: 636.680.1065
>> Cellular Phone: 314.753.7506
>> -----Original Message-----
>> From: cisco-voip-bounces at puck.nether.net
>> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Anthony
>> Mendoza
>> Sent: Sunday, June 19, 2005 1:45 PM
>> To: Cisco VoIP
>> Subject: [cisco-voip] Question on PRI Gateway
>>
>> I've got my 3640 properly configured (or so I believe), but it isn't
>> showing up as registered on my CCM (4.x).. To me it appears as
>> though the gateway is properly configured as it shows as being
>> "registered" to the primary CCM (my subscriber).
>>
>> Here's what I see on the gateway:
>>
>> rwc-faxgw-149-59#sho ccm-manager
>> MGCP Domain Name: rwc-faxgw-149-59.niku.com
>> Priority Status Host
>> ============================================================
>> Primary Registered 10.150.4.11
>> First Backup Backup Ready 10.150.4.12
>> Second Backup Backup Ready 10.150.0.13
>>
>> Current active Call Manager: 10.150.4.11
>> Backhaul/Redundant link port: 2428
>> Failover Interval: 30 seconds
>> Keepalive Interval: 15 seconds
>> Last keepalive sent: 13:41:25 PDT Jun 19 2005
>> (elapsed time:
>> 00:00:07)
>> Last MGCP traffic time: 13:41:25 PDT Jun 19 2005
>> (elapsed time:
>> 00:00:07)
>> Last failover time: None
>> Last switchback time: None
>> Switchback mode: Graceful
>> MGCP Fallback mode: Not Selected
>> Last MGCP Fallback start time: None
>> Last MGCP Fallback end time: None
>>
>> Configuration Error History:
>> FAX mode: cisco
>>
>> And
>>
>> rwc-faxgw-149-59#show mgcp
>> MGCP Admin State ACTIVE, Oper State ACTIVE - Cause Code NONE MGCP
>> call-agent: 10.150.4.11 Initial protocol service is MGCP
>> 0.1 MGCP block-newcalls DISABLED MGCP send SGCP RSIP:
>> forced/restart/graceful/disconnected DISABLED MGCP quarantine mode
>> discard/step MGCP quarantine of persistent events is ENABLED MGCP
>> dtmf-relay voip codec all mode out-of-band MGCP dtmf-relay for VoAAL2
>> disabled for all codec types MGCP voip modem passthrough disabled
>> MGCP voaal2 modem passthrough disabled MGCP voip modem relay:
>> Disabled.
>> MGCP TSE payload: 100
>> MGCP T.38 Named Signalling Event (NSE) response timer: 200 MGCP
>> Network (IP/AAL2) Continuity Test timer: 200 MGCP 'RTP stream loss'
>> timer disabled MGCP request timeout 500 MGCP maximum exponential
>> request timeout 4000 MGCP rtp unreachable timeout 1000 action notify
>> MGCP gateway port: 2427, MGCP maximum waiting delay 3000 MGCP restart
>> delay 0, MGCP vad DISABLED MGCP rtrcac DISABLED MGCP system resource
>> check DISABLED MGCP xpc-codec: DISABLED, MGCP persistent hookflash:
>> DISABLED MGCP persistent offhook: ENABLED, MGCP persistent
>> onhook: DISABLED MGCP piggyback msg ENABLED, MGCP endpoint offset
>> DISABLED MGCP simple-sdp ENABLED MGCP undotted-notation DISABLED MGCP
>> codec type g711ulaw, MGCP packetization period 20 MGCP JB threshold
>> lwm 30, MGCP JB threshold hwm 150 MGCP LAT threshold lwm 150, MGCP
>> LAT threshold hwm 300 MGCP PL threshold lwm 1000, MGCP PL threshold
>> hwm 10000 MGCP CL threshold lwm 1000, MGCP CL threshold hwm 10000
>> MGCP playout mode is adaptive 60, 40, 200 in msec MGCP Fax Playout
>> Buffer is 300 in msec MGCP media
>> (RTP) dscp: ef, MGCP signaling dscp: af31 MGCP default
>> package: trunk-package MGCP supported packages: gm-package
>> dtmf-package trunk-package line-package
>> hs-package rtp-package ms-package dt-package
>> mo-package
>> mt-package sst-package MGCP Digit Map
>> matching order: shortest match SGCP Digit Map matching
>> order: always left-to-right MGCP VoAAL2 ignore-lco-codec DISABLED
>> MGCP T.38 Fax is DISABLED MGCP T.38 Fax ECM is ENABLED MGCP T.38 Fax
>> NSF Override is DISABLED MGCP T.38 Fax Low Speed Redundancy: 0MGCP
>> T.38 Fax High Speed
>> Redundancy: 0
>> MGCP control bind :DISABLED
>> MGCP media bind :DISABLED
>> MGCP Upspeed payload type for G711ulaw: 0, G711alaw: 8 MGCP Static
>> payload type for G.726-16K codec MGCP Dynamic payload type for
>> G.726-24K codec MGCP Dynamic payload type for G.Clear codec MGCP
>> Guaranteed scheduler time is disabled
>>
>> What appears to be missing? Let me know if you need config
>> snippets...
>> Now, my PRI is not plugged in yet, but I didn't think that was
>> necessary.. Any tips are greatly appreciated!!
>>
>> Thanks,
>> --
>> Anthony Mendoza
>>
>>
>> --
>> No virus found in this outgoing message.
>> Checked by AVG Anti-Virus.
>> Version: 7.0.323 / Virus Database: 267.7.8/22 - Release Date:
>> 6/17/2005
>>
>>
>>
>> CONFIDENTIALITY NOTICE: The information contained in this
> message and
>> or attachments is intended only for the person or entity to which it
>> is addressed and may contain confidential and/or privileged
> material. Any
>> review, retransmission, dissemination, copying, or other use of this
>> information by persons or entities other than the intended recipient
>> is prohibited. If you received this e-mail or its attachments in
>> error, please contact the sender and delete the material from any
> system and
>> destroy any copies.
>>
>>
>
>
> CONFIDENTIALITY NOTICE: The information contained in this message and
> or attachments is intended only for the person or entity to which it
> is addressed and may contain confidential and/or privileged material.
> Any review, retransmission, dissemination, copying, or other use of
> this information by persons or entities other than the intended
> recipient is prohibited. If you received this e-mail or its
> attachments in error, please contact the sender and delete the
> material from any system and destroy any copies.
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
CONFIDENTIALITY NOTICE: The information contained in this message and or
attachments is intended only for the person or entity to which it is
addressed and may contain confidential and/or privileged material. Any
review, retransmission, dissemination, copying, or other use of this
information by persons or entities other than the intended recipient is
prohibited. If you received this e-mail or its attachments in error,
please contact the sender and delete the material from any system and
destroy any copies.
CONFIDENTIALITY NOTICE: The information contained in this message and or
attachments is intended only for the person or entity to which it is
addressed and may contain confidential and/or privileged material. Any
review, retransmission, dissemination, copying, or other use of this
information by persons or entities other than the intended recipient is
prohibited. If you received this e-mail or its attachments in error,
please contact the sender and delete the material from any system and
destroy any copies.
CONFIDENTIALITY NOTICE: The information contained in this message and
or attachments is intended only for the person or entity to which it is
addressed and may contain confidential and/or privileged material. Any
review, retransmission, dissemination, copying, or other use of this
information by persons or entities other than the intended recipient is
prohibited. If you received this e-mail or its attachments in error,
please contact the sender and delete the material from any system and
destroy any copies.
More information about the cisco-voip
mailing list