[cisco-voip] NM-HDV2-2T1/E1 and PVDM2

[Teodor Dobrev]

Hi,

Yes you can, the configuration of the controllers is independent.The one
in the NM-HDV2 module can be the first type and the port on the VWIC
card will be the other type.It should work.

(you should probably need enough dsp resources to configure the
timeslots)

 

-----Original Message-----
From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Yinglam Cheung
Sent: Thursday, October 27, 2005 6:58 PM
To: mihi at ludens.elte.hu; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] NM-HDV2-2T1/E1 and PVDM2

 

In pratical world you probably don't see mixed T1 and E1 on the same
router,

but in the lab it definitely can save one slot for other stuff.

 

Does anyone mind trying to see you can actually mix T1 and E1 on a

NM-HDV2-T1/E1 with VWIC-MFT-T1 or VWIC-MFT-E1? I guess it should work
but

can't be sure without trying.

 

I found a useful link for this module:

 

http://www.cisco.com/en/US/customer/tech/tk652/tk653/technologies_tech_n
ote0

9186a008039c316.shtml

 

I also have same question on an AS5300..

 

-----Original Message-----

From: MIHI [mailto:mihi at ludens.elte.hu] 

Sent: Thursday, October 27, 2005 2:24 AM

To: 'Yinglam Cheung'; cisco-voip at puck.nether.net

Subject: RE: [cisco-voip] NM-HDV2-2T1/E1 and PVDM2

Importance: Low

 

see below 

 

-----Original Message-----

From: cisco-voip-bounces at puck.nether.net

[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Yinglam Cheung

Sent: Thursday, October 27, 2005 12:21 AM

To: cisco-voip at puck.nether.net

Subject: **SPAM** [cisco-voip] NM-HDV2-2T1/E1 and PVDM2

 

Hi,

 

After I read the doc for this module, I've a few questions since I never
use

this:

 

1. can the on-board T1/E1 be configured as either T1 or E1? So both
commands

"controller t1" and "controller e1" show up in the config for the same

slot/port?

 

No, first you select either E1 or T1, with "card type {t1 | e1} slot

subslot"

 

2. if answer is yes to question 1, so you can configure one port as T1
and

the other E1 if you have two ports?

 

No, they have to be the same

 

3. if answer is no to question 1, can you put in VWIC-T1 or VWIC-E1 to
have

mixed T1 and E1 ports?

 

Maybe, but why would you use both?

 

4. can you mix PVDM2 and PVDM in the same NM?

 

Only PVDM2

 

Thanks!

_______________________________________________

cisco-voip mailing list

cisco-voip at puck.nether.net

https://puck.nether.net/mailman/listinfo/cisco-voip

 

_______________________________________________

cisco-voip mailing list

cisco-voip at puck.nether.net

https://puck.nether.net/mailman/listinfo/cisco-voip

-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20051028/8e76a20f/attachment.html