[cisco-voip] CallManager Problem - Make outside call

Alan Su cj.alan at gmail.com
Tue Apr 11 11:42:11 EDT 2006


Hi Kelvin,

Thanks a lot, I'll study those valuable documents you share with me.
Regarding the dialing pattern, I also have below questions:
1. What if I'm in out of US ? Do I still can use @ for typical north
American dial plan ?

2. Can user only dial one digit (ex:9), and after hearing the dial tone then
begin to dial the outside number? In this case, I can't set the full pattern
in my route pattern, how should I configure it ?

Many many thanks for your help.


Regards,

Alan


2006/4/11, Kevin Thorngren <kthorngr at cisco.com>:
>
> Hi Alan,
>
> The 9. pattern needs to match the full pattern you are using.  Some
> examples are:
>
> 9.@ - typical north American dial plan macro that matches local, ld and
> international patterns.
> 9.[2-9]XXXXXX - More specific pattern for local 7 digit dialing
> 9.1[2-9]XX[2-9]XXXXXX - More specific pattern for LD dialing
> 9.011T - More specifc pattern for international dialing
>
> The CCM will need to match the full pattern dialed from the phone
> before extending the call to the GW.  With 9. the GW is receiving a
> blank dialed number (assuming you are doing pre-dot discard).  Also you
> will want to select the option for outside dialtone.  The below links
> should help describe this.
>
> http://www.cisco.com/en/US/products/sw/voicesw/ps556/
> products_tech_note09186a0080094b2a.shtml
>
> http://www.cisco.com/en/US/products/sw/voicesw/ps556/
> products_tech_note09186a00800945b9.shtml
>
> http://www.cisco.com/en/US/products/sw/voicesw/ps556/
> products_administration_guide_chapter09186a00803edabe.html
>
> http://www.cisco.com/en/US/products/sw/voicesw/ps556/
> products_administration_guide_chapter09186a00803ed685.html
>
> HTH,
> Kevin
> On Apr 11, 2006, at 7:47 AM, Alan Su wrote:
>
> > Dear All,
> >
> > My IPT architecture is: CCM(4.02) + Voice Gateway(3745 runing MGCP w/
> > E1 PRI trunk to PSTN).
> > I already configured the MGCP and ccm-manager option in the voice
> > gateway, and it's registered to CM without any problem.
> > I also made the gateway configuratio in CCM to this router.
> >
> > Right now my problem is, I don't know how to setup the route pattern
> > to allow IP Phone to make outside call.
> > My idea is, when user dial "9", the phone will provide an outside dial
> > tone and user can directly dial the PSTN phone number to complete a
> > call (just like the old fashion way). But when I configure the route
> > pattern "9." and set the S1/DS1-0 at VGW to be the gateway, there is
> > nothing but a "Bad Address".
> >
> > Does anyone know how to find the reference document for the
> > configuration or how to fix this problem? I did lots of search but
> > nothing found. Any comment would be very grateful. Thanks a lot ~
> >
> >
> > Regards,
> >
> > Alan
> > <VGW-Config.txt>_______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20060411/091fd6a7/attachment.html 


More information about the cisco-voip mailing list