[cisco-voip] Dial-peer matching question

[Mike Mike]

Are you using this as a guide?

http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a00800942a5.shtml


On 8/10/06, Keith Klevenski <keith.klevenski at rig.net> wrote:
>
>   I'd be curious what 'sh dialplan num 39495' showed…
>
>
>  ------------------------------
>
> *From:* cisco-voip-bounces at puck.nether.net [mailto:
> cisco-voip-bounces at puck.nether.net] *On Behalf Of *Ed Leatherman
> *Sent:* Thursday, August 10, 2006 1:14 PM
> *To:* cisco-voip at puck.nether.net
> *Subject:* [cisco-voip] Dial-peer matching question
>
>
>
> I'm having trouble getting inbound dial-peers to match up. I have the
> following scenario
>
>
>
> voice-port 0/1/1
>
>  connection plar 39495
>
>  caller-id enable
>
> !
> dial-peer voice 1 pots
>  description Inbound pots dial-peer for port 0/1/1
>  incoming called-number 39495
> !
> dial-peer voice 300 voip
>  description outbound dial-peer to callmanager 10.182.140.10
>  destination-pattern 39495
>  session target ipv4:10.182.140.10
> !
>
>
>
> Unfortunately when I watch the debug voice ccapi inout for a call to that
> FXO port, it is always matching dial-peer 0.
>
> ug 10 18:08:45.958: //-1/195B3C298092/CCAPI/cc_api_display_ie_subfields:
>    cc_api_call_setup_ind_common:
>    cisco-username=
>    ----- ccCallInfo IE subfields -----
>    cisco-ani=
>    cisco-anitype=0
>    cisco-aniplan=0
>    cisco-anipi=0
>    cisco-anisi=0
>    dest=39495
>    cisco-desttype=0
>    cisco-destplan=0
>    cisco-rdie=FFFFFFFF
>    cisco-rdn=
>    cisco-rdntype=0
>    cisco-rdnplan=0
>    cisco-rdnpi=0
>    cisco-rdnsi=0
>    cisco-redirectreason=0   fwd_final_type =0
>    final_redirectNumber =
>    hunt_group_timeout =0
>
> Aug 10 18:08:45.958: //-1/195B3C298092/CCAPI/cc_api_call_setup_ind_common:
>    Interface=0x46A538BC, Call Info(
>    Calling Number=,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=Not
> Screened, Presentation=Al
> lowed),
>    Called Number=39495(TON=Unknown, NPI=Unknown),
>    Calling Translated=FALSE, Subscriber Type Str=RegularLine,
> FinalDestinationFlag=TRUE,
> *   Incoming Dial-peer=0*, Progress Indication=ORIGINATING SIDE IS NON
> ISDN(3), Calling IE Present=FAL
> SE,
>    Source Trkgrp Route Label=, Target Trkgrp Route Label=, CLID
> Transparent=FALSE), Call Id=-1
>
> I've also tried replacing the incoming called-number with "port 0/1/1" to
> force it to match on that criteria, but it doesnt match that either. I need
> to get the inbound dialpeer nailed down, because when I put the rest of my
> dial-peers in, it inevitably chooses another dial-peer in my config and uses
> that destination-patters as an incorrect number for the callerID.
>
> From what I read on cco, the incoming called-number should take precidence
> and cause it to match. Maybe this doesnt work because its a PLAR
> configuration.. But then when I tried the voice-port, that should have
> matched. Its the the port that is ringing in and its the first dial-peer in
> the config.
>
>
>
> Any ideas what i'm doing wrong here?
>
>
> --
> Ed Leatherman
> Senior Voice Engineer
> West Virginia University
> Telecommunications and Network Operations
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20060810/afda444f/attachment.html