[cisco-voip] Reset an FXO port

[Todd Franklin]

Yeah I did that.  But still no go.
Here is the sho voice port 0/0/0 command output:

ho voice port 0/0/0

Foreign Exchange Office 0/0/0 Slot is 0, Sub-unit is 0, Port is 0
 Type of VoicePort is FXO
 Operation State is DORMANT
 Administrative State is UP
 The Last Interface Down Failure Cause is Administrative Shutdown
 Description is 555-123-4567
 Noise Regeneration is enabled
 Non Linear Processing is enabled
 Non Linear Mute is disabled
 Non Linear Threshold is -21 dB
 Music On Hold Threshold is Set to -38 dBm
 In Gain is Set to 0 dB
 Out Attenuation is Set to 3 dB
 Echo Cancellation is enabled
 Echo Cancellation NLP mute is disabled
 Echo Cancellation NLP threshold is -21 dB
 Echo Cancel Coverage is set to 48 ms
 Echo Cancel worst case ERL is set to 6 dB
 Playout-delay Mode is set to adaptive
 Playout-delay Nominal is set to 60 ms
 Playout-delay Maximum is set to 250 ms
 Playout-delay Minimum mode is set to default, value 40 ms
 Playout-delay Fax is set to 300 ms
 Connection Mode is plar
 Connection Number is 2002
 Initial Time Out is set to 10 s
 Interdigit Time Out is set to 10 s
 Call Disconnect Time Out is set to 60 s
 Ringing Time Out is set to 180 s
 Wait Release Time Out is set to 30 s
 Companding Type is u-law
 Region Tone is set for US

 Analog Info Follows:
 Currently processing none
 Maintenance Mode Set to None (not in mtc mode)
 Number of signaling protocol errors are 0
 Impedance is set to 600r Ohm
 Station name None, Station number None
 Translation profile (Incoming):
 Translation profile (Outgoing):

 Voice card specific Info Follows:
 Signal Type is loopStart
 Battery-Reversal is enabled
 Number Of Rings is set to 1
 Supervisory Disconnect is signal
 Answer Supervision is inactive
 Hook Status is On Hook
 Ring Detect Status is inactive
 Ring Ground Status is inactive
 Tip Ground Status is inactive
 Dial Out Type is dtmf
 Digit Duration Timing is set to 100 ms
 InterDigit Duration Timing is set to 100 ms
 Pulse Rate Timing is set to 10 pulses/second
 InterDigit Pulse Duration Timing is set to 750 ms
 Percent Break of Pulse is 60 percent
 GuardOut timer is 2000 ms
 Minimum ring duration timer is 125 ms
 Hookflash-in Timing is set to 600 ms
 Hookflash-out Timing is set to 500 ms
 Supervisory Disconnnct Timing is set to 350 ms

I think I am missing something basic.  This has happened before and the only
way to fix it was to reboot the 2801.

Todd

On 4/30/07, Adam <cisco at adman.net> wrote:
>
> How about a 'shutdown' followed by 'no shutdown' in the voice-port
> configuration?
>
> -Adam
>
> On 4/30/07, Todd Franklin <toddnh65 at gmail.com> wrote:
> > Apparently my FXO port is hung internally.  I can't easily reboot this
> box
> > since it has my PRI on it as well.
> > Is there a command to just reset the FXO port?  Right now I have my
> telco
> > busying it out so it will fall over to the next line (which comes in on
> the
> > PRI).
> >
> > Thanks anyone!
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> >
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20070430/2622e2f1/attachment-0001.html