[cisco-voip] RightFax

[Joel Perez]

Okay,

Ignore this, i had an incorrect crossover cable. Made a correct one and now
the t-1 is up on both sides.
Realized it after I replied to Senthil.

Joel P.


On 12/28/07, Joel Perez <tman701 at gmail.com> wrote:
>
> Hey Senthil,
>
> Here is my output:
>
> ISDN Serial0/1/1:23 interface
>         ******* Network side configuration *******
>         dsl 3, interface ISDN Switchtype = primary-4ess
>         L2 Protocol = Q.921 0x0000  L3 Protocol(s) = CCM MANAGER 0x0003
>     Layer 1 Status:
>         DEACTIVATED
>     Layer 2 Status:
>         TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
>     Layer 3 Status:
>         0 Active Layer 3 Call(s)
>     Active dsl 3 CCBs = 0
>     The Free Channel Mask:  0x00000000
>     Number of L2 Discards = 0, L2 Session ID = 2
>     Total Allocated ISDN CCBs = 0
>
> Another thing I forgot to mention was that the board comes with a straight
> thru cable but i tried also a crossover cable.
> Same results.
>
> Joel P
>
>
>  On 12/28/07, senthil natarajan <senccie at gmail.com> wrote:
> >
> > what is the status of "sh isdn status"
> >
> > layer 1 - active
> > layer 2 - multiple frame established
> > layer 3 - backhauled to CCM ?
> >
> > -senthil
> >
> >
> >  On Dec 28, 2007 1:21 PM, Joel Perez <tman701 at gmail.com> wrote:
> >
> > >  Hey Guys,
> > >
> > > I seem to have hit a stumbling block setting up a RightFax server V9.3and a Brooktrout TR1034 card.
> > > I cant get the T-1 to come up.
> > > The way its set up is the BrookTrout card goes to a
> > > VWIC2-2MFT-T1/E1-T1 port on my 2851.
> > > I am using CUCM 5.1.1 and MGCP on that T1 port on the 2851. My config
> > > on the 2851 is as follows.
> > >
> > > controller T1 0/1/1
> > >  framing esf
> > >  clock source internal
> > >  linecode b8zs
> > >  pri-group timeslots 1-24 service mgcp
> > > !
> > >
> > > interface Serial0/1/1:23
> > >  no ip address
> > >  isdn switch-type primary-4ess
> > >  isdn protocol-emulate network
> > >  isdn incoming-voice voice
> > >  isdn bind-l3 ccm-manager
> > >  no cdp enable
> > >
> > >
> > > On the Brooktrout card on the "PortA" tab I have the following:
> > > Switch Type : AT&T #4 ESS
> > > Protocol (Variant):  Bellcore national ISDN-1 Standard
> > > Emulation: CPE
> > > Line Coding B8ZS
> > >
> > > On the "Clock settings" tab i have:
> > > Clock Mode: Master
> > > Clock Source : Network Trunk Port A
> > > Clock Compatibility: None
> > >
> > >
> > > I tried getting their Tech support to help but they pointed fingers at
> > > the CUCM and said they couldnt help me any further.
> > >
> > > Thanks,
> > >
> > > Joel P
> > >
> > >
> > > _______________________________________________
> > > cisco-voip mailing list
> > > cisco-voip at puck.nether.net
> > > https://puck.nether.net/mailman/listinfo/cisco-voip
> > >
> >
> >
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20071228/5e60d276/attachment.html