[cisco-voip] CCM shared line like in CME

[Jozef Janitor]

Thank you Scott.

Have a nice day.

Jozef

> -----Original Message-----
> From: Voll, Scott [mailto:Scott.Voll at wesd.org]
> Sent: Thursday, January 04, 2007 11:58 PM
> To: Jozef Janitor; Patrick Mowry; cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] CCM shared line like in CME
> 
> Setup a Broad cast LineGroup... assign it to a Hunt Group and then to a
> Hunt pilot.  It will work much the same way.
> 
> Scott
> 
> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Jozef Janitor
> Sent: Thursday, January 04, 2007 2:43 PM
> To: 'Patrick Mowry'; cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] CCM shared line like in CME
> 
> We have an office where each of us has its own IP phone at the desk
> with
> own
> extension, but we would like also to have one shared number for this
> office.
> 
> There are already no free buttons on the phones, so that's the reason
> why I
> would like to have to one button assigned two extensions.
> 
> Is it possible?
> 
> Thank you.
> 
> Jozef
> 
> 
> > -----Original Message-----
> > From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-
> > bounces at puck.nether.net] On Behalf Of Patrick Mowry
> > Sent: Thursday, January 04, 2007 11:13 PM
> > To: cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] CCM shared line like in CME
> >
> > Just out of curiosity, what is it you are trying to do?
> > The only time I have used an overlay button in CME was to simulate
> the
> > operation of a broadcast hunt group that is native to CM, but not in
> > CME.
> >
> > -Patrick
> >
> >   ----- Original Message -----
> >   From: Jozef Janitor
> >   To: cisco-voip at puck.nether.net
> >   Sent: Thursday, January 04, 2007 2:56 PM
> >   Subject: [cisco-voip] CCM shared line like in CME
> >
> >
> >   Hi,
> >
> >
> >
> >   Is it possible to configure the "big" CCM (4.x) to have a shared
> line
> > feature assigned to a button?
> >
> >   I am creating these shared lines on CME this way:
> >
> >
> >
> >   ephone-dn 1
> >
> >    number 1000
> >
> >   ephone-dn 2
> >
> >    number 1001
> >
> >   ephone 1
> >
> >    mac-address 1234.5678.1234
> >
> >    type 7940
> >
> >    button 1o1,2
> >
> >
> >
> >   But in CCM configuration I can't see a possibility to assign
> another
> > DN to a line.
> >
> >   Do you have any suggestion please?
> >
> >
> >
> >   Thank you.
> >
> >
> >
> >   Best regards,
> >
> >      Jozef Janitor
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> 
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip