[cisco-voip] Dial-peer voip with dest-patt starting # and CME4.0.1

[Erik Goppel]

Paul,

conf t
no dial-peer terminator #
dial-peer terminator A



2007/9/6, Paul Choi <asobihoudai at yahoo.com>:
>
> Erik,
>
> Hi, how did you manage to do this?
>
> Paul
> --- Erik Goppel <egoppel at gmail.com> wrote:
>
> > I have found the solution to the problem.
> > i have changed the dial-peer terminator to a
> > character A and disabled the
> > terminator #
> > this was blocking the # dialing, besides the bulk
> > speeddial issue.
> >
> >
> > grtz
> >
> > erik
> >
> >
> > 2007/9/3, Clouse, Chris <chris.clouse at berbee.com>:
> > >
> > >  There is a command on the router to disable # as
> > a special access
> > > character.  It escapes me at the moment, but I
> > know it exists.
> > >
> > >
> > >
> > > *From:* cisco-voip-bounces at puck.nether.net
> > [mailto:
> > > cisco-voip-bounces at puck.nether.net] *On Behalf Of
> > *Erik Goppel
> > > *Sent:* Sunday, September 02, 2007 3:51 PM
> > > *To:* Paul Choi
> > > *Cc:* ciscovoip
> > > *Subject:* Re: [cisco-voip] Dial-peer voip with
> > dest-patt starting # and
> > > CME4.0.1
> > >
> > >
> > >
> > > Paul,
> > >
> > >
> > >
> > > that`s what i thought as well, however in CME
> > 4.0.1 it just doesn`t work.
> > >
> > > i`ve created a dial-peer with a
> > destination-pattern starting with a #, but
> > > as soon as i lift up the handset, and press # and
> > the next digit, the call
> > > sends out the reorder tone.
> > >
> > > so i have been researching lots of documents, and
> > finally found a user
> > > guide for cme 4.0.1 which states that a user is
> > able to program their
> > > personal speed dials in this way.
> > >
> > > user goes offhook
> > >
> > > press #
> > >
> > > press speeddial
> > >
> > > enter destination
> > >
> > > press speeddial again
> > >
> > > and your speeddial is programmed.
> > >
> > >
> > >
> > > if i analyse this flow, it means i cannot use a
> > destination-pattern
> > > starting with a #
> > >
> > > I don`t need users to be able to program their own
> > speeddials, so if i can
> > > disable this, i will be very happy, however i
> > cannot find anything that can
> > > disable this behaviour.
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > thanks,
> > >
> > >
> > >
> > > erik
> > >
> > >
> > >
> > > 2007/9/2, Paul Choi <asobihoudai at yahoo.com>:
> > >
> > > Erik,
> > >
> > > says here....
> > >
> > >
> > >
> >
>
> http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a0080080aec.html
> > >
> > > In addition to wildcard characters, the following
> > > characters can also be used in the destination
> > > pattern:
> > >
> > > •Asterisk (*) and pound sign (#)—These characters
> > on
> > > standard touch-tone dial pads can be used anywhere
> > in
> > > the pattern. They can be used as the leading
> > character
> > > (for example, *650), except on the Cisco 3600
> > series.
> > >
> > > •Dollar sign ($)—Disables variable-length
> > matching.
> > > Must be used at the end of the dial string.
> > >
> > > The same destination pattern can be shared across
> > > multiple dial peers to form hunt groups. For
> > > information on building hunt groups, see the "Hunt
> > > Groups and Preferences" section.
> > >
> > > For information on how the terminating router
> > strips
> > > off digits after matching a destination pattern,
> > see
> > > the "Digit Stripping on Outbound POTS Dial Peers"
> > > section.
> > >
> > > So if you set a pattern as such, you should be
> > able to
> > > use it without issue. Make sure your set your
> > > interdigit timeout to something reasonable.
> > >
> > > Paul
> > >
> > > --- Erik Goppel < egoppel at gmail.com> wrote:
> > >
> > > > Hi,
> > > >
> > > >
> > > > does anyone know if it is possible to use a # as
> > a
> > > > prefix in voip dial-peer
> > > > while using CME on the same router?
> > > > My current CME is blocking the # because of the
> > > > personal speeddial edting
> > > > feature which utilizes a # after lifting the
> > > > handset.
> > > >
> > > >
> > > > example:
> > > >
> > > > dial-peer voice 10 voip
> > > > destination-pattern #1234
> > > > session-target (whatever)
> > > >
> > > >
> > > > I need to use the pound because the cusomer
> > insists
> > > > on using a pound prefix
> > > > as a trunk prefix to another site.(yes i know)
> > >
> > >
> > >
> > >
> > >
> >
>
> ____________________________________________________________________________________
> > >
> > > Sick sense of humor? Visit Yahoo! TV's
> > > Comedy with an Edge to see what's on, when.
> > > http://tv.yahoo.com/collections/222
> > >
> > >
> > >
> > > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
>
>
> ____________________________________________________________________________________
> Pinpoint customers who are looking for what you sell.
> http://searchmarketing.yahoo.com/
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20070912/c9947417/attachment.html