[cisco-voip] Antw: Analog phones cant transfer calls on 2811 acting asH323 gw to UCM 4.2 (3)

[Ted Nugent]

If you need features with fxs you might want to look into SCCP for FXS
controller as you would with a VG224 and h323 for and PSTN/PRI access etc.
(see the link you need CM4.2+ and a certain rev of IOS depending on your
hardware).

http://www.cisco.com/en/US/partner/products/ps6441/products_feature_guide09186a0080483a76.html#wp1304455

<http://www.cisco.com/en/US/products/ps6706/products_feature_guide09186a00806cab75.html#wp1049404>





On 9/20/07, Cucumber Green <greencucumber2007 at yahoo.com> wrote:
>
> Hello!
>
> Yeah I have tried this without luck, I guess it only works if the H323
> gateway has a FXO
> connection to a PBX
>
> *Robert Schuknecht <rschuknecht at gmx.de>* wrote:
>
> Hi Cucumber,
>
> did you try to adjust the the hook-flash timer under the voice-port?
> This timer has to equal on the voice-port and the connected telephone.
>
> /Robert
>
> >>> Cucumber Green schrieb am Donnerstag, 20.
> September 2007 um 17:53 in Nachricht 3ab0adee131ef58c7afb0ea50017a410:
> > Analog phones can send and receive calls from IP phones, but
> > when pressing the hookflash key at the analog phone, the analog phone
> does
> > not get a dial tone in order to transfer the call :(
> >
> > Phones are hooked into FXS ports on a 2811 and will use G729 codec.
> >
> > I have already checked the "Media Termination Point required" check box
> in
> > the gateway configuration at call manager (using unified call manager
> 4.2(3)
> > ). I thought that would do the trick, but it didnt, any ideas?
> >
> > This is the gateway config (IOS version 12.4(3g) spservicesK9)
> >
> > !
> > version 12.4
> > service timestamps debug datetime msec
> > service timestamps log datetime msec
> > service password-encryption
> > !
> > ip subnet-zero
> > !
> > !
> > ip cef
> > !
> > !
> > no ip domain lookup
> > !
> > voice-card 0
> > no dspfarm
> > !
> > !
> > !
> > !
> > interface Loopback0
> > ip address X.X.X.X 255.255.255.255
> > h323-gateway voip bind srcaddr X.X.X.X
> > !
> > !
> > ip classless
> > ip route 0.0.0.0 0.0.0.0 X.X.X.X 254
> > !
> > !
> > control-plane
> > !
> > !
> > !
> > voice-port 0/1/0
> > signal loopStart
> > !
> > voice-port 0/1/1
> > signal loopStart
> > !
> > dial-peer voice 10 pots
> > destination-pattern 50001
> > port 0/1/0
> > !
> > dial-peer voice 20 pots
> > destination-pattern 50002
> > port 0/1/1
> > !
> > dial-peer voice 1 voip
> > preference 1
> > destination-pattern 1...
> > session target ipv4:X.X.X.X
> > dtmf-relay h245-alphanumeric
> > codec g729r8 bytes 40
> > ip qos dscp cs3 media
> > ip qos dscp cs3 signaling
> > !
> > dial-peer voice 4 voip
> > preference 2
> > destination-pattern 1...
> > session target ipv4:X.X.X.X
> > dtmf-relay h245-alphanumeric
> > codec g729r8 bytes 40
> > ip qos dscp cs3 media
> > ip qos dscp cs3 signaling
> > !
> >
> >
> >
> > ---------------------------------
> > Be a better Globetrotter. Get better travel answers from someone who
> knows.
> > Yahoo! Answers - Check it out.
>
>
>  ------------------------------
> Don't let your dream ride pass you by. Make it a reality<http://us.rd.yahoo.com/evt=51200/*http://autos.yahoo.com/index.html;_ylc=X3oDMTFibjNlcHF0BF9TAzk3MTA3MDc2BHNlYwNtYWlsdGFncwRzbGsDYXV0b3MtZHJlYW1jYXI->with Yahoo! Autos.
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20070920/629640ab/attachment.html