[cisco-voip] 7970 won't get new code...

[Jonathan Charles]

OK, it worked... doesn't make it less annoying tho...



Jonathan

On Fri, Apr 4, 2008 at 7:23 PM, Jonathan Charles <jonvoip at gmail.com> wrote:
> OK, I am getting the zip, and I will upload them as individual files
>  to the TFTP...
>
>  This is annoying.
>
>
>  Jonathan
>
>
>
>  On Fri, Apr 4, 2008 at 7:21 PM, Jonathan Charles <jonvoip at gmail.com> wrote:
>  > OK, you can't
>  >
>  >  So, they are screwed.
>  >
>  >
>  >
>  >  Jonathan
>  >
>  >
>  >
>  >  On Fri, Apr 4, 2008 at 7:20 PM, Jonathan Charles <jonvoip at gmail.com> wrote:
>  >  > Crap.
>  >  >
>  >  >  Ok, fine... can I get 7.0(3) on a CCM 5.1?
>  >  >
>  >  >
>  >  >
>  >  >  Jonathan
>  >  >
>  >  >
>  >  >
>  >  >  On Fri, Apr 4, 2008 at 6:25 PM, Pat Hayes <pat-cv at wcyv.com> wrote:
>  >  >  > You  might consider consulting the readme for 8.3.4sr1, the first note in
>  >  >  > the upgrade caveat section is:
>  >  >  >
>  >  >  >  "If you are currently running firmware earlier than 6.0(2) on a Cisco
>  >  >  > Unified IP Phone 7970G or 7971G-GE and want to upgrade to 8.0(x), you must
>  >  >  > first install an intervening 7.0(x) load to prevent upgrade failure. Cisco
>  >  >  > recommends using the most recent 7.0(3) load as the
>  >  >  >  intervening load to avoid lengthy upgrade times (see next item)."
>  >  >  >
>  >  >  >
>  >  >  >  -------- Original Message  --------
>  >  >  >  From: "Jonathan Charles" <jonvoip at gmail.com>
>  >  >  >  To: "Robert Kulagowski" <rkulagow at gmail.com>
>  >  >  >  Cc: "cisco-voip at puck.nether.net" <cisco-voip at puck.nether.net>
>  >  >  >  Subject: [cisco-voip] 7970 won't get new code...
>  >  >  >
>  >  >  >  Date: 4/4/2008 6:30 PM
>  >  >  >
>  >  >  >
>  >  >  > >
>  >  >  > >
>  >  >  > >
>  >  >  > > OK, this is too much work... why isn't the phone getting the new code?
>  >  >  > >
>  >  >  > >
>  >  >  > > Jonathan
>  >  >  > >
>  >  >  > > On Fri, Apr 4, 2008 at 5:14 PM, Robert Kulagowski <rkulagow at gmail.com>
>  >  >  > wrote:
>  >  >  > >
>  >  >  > > > Jonathan Charles wrote:
>  >  >  > > >
>  >  >  > > >
>  >  >  > > > > The oldest SCCP 7970 load is SCCP70.8-2-2SRS2s and I tried that...
>  >  >  > > > >
>  >  >  > > > > I cannot id any older load...
>  >  >  > > > >
>  >  >  > > > >
>  >  >  > > >  You could do this incrementally if you don't want to mess with your
>  >  >  > live
>  >  >  > > > config on CM.  If you have a router and a switch that you can isolate
>  >  >  > from
>  >  >  > > > the rest of your network, you could put the router into "CME" mode
>  >  >  > > > temporarily and load it up with the old phone loads from CCO, then have
>  >  >  > the
>  >  >  > > > phones load intermediate firmwares off of that until they can bootstrap
>  >  >  > > > themselves to 8.3.3 that you're running in production.
>  >  >  > > >
>  >  >  > > >  Let me know if you need an example CME config.
>  >  >  > > >
>  >  >  > > >
>  >  >  > >
>  >  >  > > _______________________________________________
>  >  >  > > cisco-voip mailing list
>  >  >  > > cisco-voip at puck.nether.net
>  >  >  > > https://puck.nether.net/mailman/listinfo/cisco-voip
>  >  >  > >
>  >  >  >
>  >  >
>  >
>