[cisco-voip] multiple auto-attendant scripts on NME-CUE

[Lelio Fulgenzi]

The AA's won't be used at the same time, it's either one or the other, so I 
want to be able to use all ports for each AA.

--------------------------------------------------------------------------------
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"Life expectancy would grow by leaps and bounds if green vegetables smelled 
as good as bacon."
Doug Larson


----- Original Message ----- 
From: "Jim McBurnett" <jim at tgasolutions.com>
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>; "Matthew Saskin" <matt at saskin.net>
Cc: "Cisco VoIPoE List" <cisco-voip at puck.nether.net>
Sent: Wednesday, February 06, 2008 10:43 PM
Subject: RE: [cisco-voip] multiple auto-attendant scripts on NME-CUE


> Just consider the slicing of the port counts up..
> 3 port to AA # 1, 6 ports to AA #2 etc...
>
> Jim
>
> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net 
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Lelio Fulgenzi
> Sent: Wednesday, February 06, 2008 11:57 AM
> To: Matthew Saskin
> Cc: Cisco VoIPoE List
> Subject: Re: [cisco-voip] multiple auto-attendant scripts on NME-CUE
>
> That's what I thought....thanks for the feedback.
>
> ----- Original Message -----
> From: "Matthew Saskin" <matt at saskin.net>
> To: "Lelio Fulgenzi" <lelio at uoguelph.ca>
> Cc: "Cisco VoIPoE List" <cisco-voip at puck.nether.net>
> Sent: Wednesday, February 06, 2008 11:52 AM
> Subject: Re: [cisco-voip] multiple auto-attendant scripts on NME-CUE
>
>
>> As for running multiple AA scripts, it's just a matter of uploading the
>> multiple .aef files to the CUE module.  Since you want to run them only
>> when the site is in SRST mode, it should just be a matter of properly
>> configuring the SIP subsystem on the CUE, setting up the triggers, and
>> proper configuration of the dial-peers on the host router to send the
>> calls to the proper trigger/auto-attendant.
>>
>> -matt
>>
>> Lelio Fulgenzi wrote:
>>> I'd like to be able to run multiple auto-attendant scripts on an NME-CUE
>>> module. Is this possible?
>>>  Basically, I'd like to decommission a couple of MCS servers that we are
>>> running IPIVR 3.5 (or something) on as our backup auto-attendant and 
>>> move
>>> these over to a few 3845s we are planning on purchasing outfitted with
>>> NME-CUE modules.
>>>  Here's the wrinkle, I'd also like to run a system down autoattendant
>>> that kicks in when the routers lose connectivity with the cluster, i.e.
>>> system down and trunks register via H323/SRST.
>>>  And I'd like both scripts to be able to use the maximum number of 
>>> ports,
>>> since only one will usually be active at once.
>>>  I'm pretty sure I can do this according to what I see on my AIM-CUE 
>>> gui.
>>>  Comments?
>>> --------------------------------------------------------------------------------
>>> Lelio Fulgenzi, B.A.
>>> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
>>> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
>>> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
>>> "Buffalo buffalo Buffalo buffalo buffalo buffalo Buffalo buffalo."
>>> WJR
>>>
>>>
>>> ------------------------------------------------------------------------
>>>
>>> _______________________________________________
>>> cisco-voip mailing list
>>> cisco-voip at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>