[cisco-voip] using my DSPs on a 3845

[Lelio Fulgenzi]

Thanks J,


------------------------------------------------------------------------------

          PVDM Slot 0:
          64-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
          Hardware Revision        : 4.0
          Part Number              : 73-8541-05
          Board Revision           : B0
          Deviation Number         : 0
          Fab Version              : 04
          PCB Serial Number        : FOC11165C5C
          RMA Test History         : 00
          RMA Number               : 0-0-0-0
          RMA History              : 00
          Processor type           : 00
          Product (FRU) Number     : PVDM2-64


------------------------------------------------------------------------------

--------------------------------------------------------------------------------
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
"Life expectancy would grow by leaps and bounds if green vegetables smelled as good as bacon."
Doug Larson


----- Original Message ----- 
From: "Jonathan Charles" <jonvoip at gmail.com>
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>
Cc: "Cisco VoIPoE List" <cisco-voip at puck.nether.net>
Sent: Friday, January 25, 2008 5:12 PM
Subject: Re: [cisco-voip] using my DSPs on a 3845


> Do a show diag to see what hardware is in the router...
> 
> 
> Jonathan
> 
> On Jan 25, 2008 2:20 PM, Lelio Fulgenzi <lelio at uoguelph.ca> wrote:
>>
>>
>> I've got a 3845 with a PVDM2-64 as far as I can tell. Well, that's what I
>> ordered and I trust Cisco! A "show voice dsp" shows the following:
>>
>> DSP   DSP              DSPWARE CURR  BOOT                         PAK
>> TX/RX
>> TYPE  NUM CH CODEC     VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK
>> COUNT
>> ===== === == ========= ======= ===== ======= === == ========= == ====
>> ============
>> C5510 001 01 g711ulaw    9.2.2 busy  idle      0  0 0/0/0:23  23    0
>> 11621/11516
>> C5510 001 02 g711ulaw    9.2.2 busy  idle      0  0 0/1/0:23  22    0
>> 63104/64754
>> C5510 001 03 g711ulaw    9.2.2 busy  idle      0  0 0/0/0:23  07    0
>> 4906/4634
>> C5510 001 04 None        9.2.2 idle  idle      0  0                 0
>> 0/0
>> <snip>
>> C5510 004 15 None        9.2.2 idle  idle      0  0                 0
>> 0/0
>> C5510 004 16 None        9.2.2 idle  idle      0  0                 0
>> 0/0
>> ------------------------END OF FLEX VOICE CARD 0
>> ----------------------------
>> I gather that each DSP can handle 16 voice calls, so if I have two T1s = 23
>> calls * 2 (each has their own Dchannel)=46 calls / 16 = 2.875.
>>
>> So that means three DSPs are required to handle my voice calls and I have
>> one left for conferencing.
>>
>> Do I just create a DSP farm with one DSP and somehow assign it as a
>> conference resource in Call Manager?
>>
>> Lelio
>> --------------------------------------------------------------------------------
>> Lelio Fulgenzi, B.A.
>> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
>> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
>> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
>> "Buffalo buffalo Buffalo buffalo buffalo buffalo Buffalo buffalo."      WJR
>>
>>
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20080125/c1328f4b/attachment.html