[cisco-voip] selectively pick a BRI or PRI from differentextensions behind call manager

[Matthew Saskin]

Lelio's suggestion would work perfectly using MGCP gateways.  As an 
alternative (if you want to use H.323) you can use distinct 
CSS/Partition/RP's as with H.323 but instead of differentiating at the 
route group/route list level, you'd have to add a prefix on outbound 
calls and use different dial-peers on the gateway to match.

-matt

Lelio Fulgenzi wrote:
> Calling search space assigned to the different classes would hit 
> different partitions with different route patterns assigned to different 
> gateways.
>  
> So, phone A with CSS A hits 9.@ in Partition A which sends calls out BRI A.
> And, phone B with CSS B hits 9.@ in Partition B which sends calls out BRI B.
>  
> I'm not aware of any way (with MGCP anyways) to send calls out specific 
> channels on a BRI/PRI.
>  
> --------------------------------------------------------------------------------
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> “Life expectancy would grow by leaps and bounds if green vegetables 
> smelled as good as bacon.”
> Doug Larson
>  
>  
> 
>     ----- Original Message -----
>     *From:* Erik Erasmus (E) <mailto:ErasmuE4 at telkom.co.za>
>     *To:* cisco-voip at puck.nether.net <mailto:cisco-voip at puck.nether.net>
>     *Sent:* Monday, January 28, 2008 11:54 PM
>     *Subject:* [cisco-voip] selectively pick a BRI or PRI from
>     differentextensions behind call manager
> 
>     Does anyone have experience in selecting a specific ISDN basic rate
>     or primary rate line on a voice gateway from a call manager and what
>     would be the best way to do it.
> 
>      
> 
>     I have a solution where two businesses will share a gateway and they
>     will each have a separate BRI to keep pstn billing separate – they
>     share a call manager. How would one make a specific range of
>     extensions always pick one BRI when dialing out to pstn and another
>     range select another BRI on the same gateway preferably.
> 
>      
> 
>     If possible I want to use a single gateway
> 
>     With two gateways I guess it would be a lot easier – possible using
>     different pstn access codes and then selecting different route
>     patterns / rlists/ routegroups / gateway  
> 
>      
> 
>     I am not too fussy about h323 versus mgcp – but have more h323
>     experience so will probably prefer this
> 
>      
> 
>      
> 
>     Any advice will be appreciated
> 
>      
> 
>      
> 
>      
> 
>     Erik Erasmus
> 
>     \
> 
>     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>     This e-mail is subject to the Telkom SA electronic communication
>     legal notice, available at :
>     http://www.telkom.co.za/TelkomEMailLegalNotice.PDF
>     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> 
>     ------------------------------------------------------------------------
> 
>     _______________________________________________
>     cisco-voip mailing list
>     cisco-voip at puck.nether.net
>     https://puck.nether.net/mailman/listinfo/cisco-voip
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip