[cisco-voip] cme/PRI newbie question

[Kelemen Zoltan]

Are the incoming DiD numbers assigned to phones? Or transformed/routed 
to them? Depending on how many digits you receive from the provider as 
called number, you might need to do some number translations on the 
called number to make sure the calls reach your phones.

As Erick noted, once you know your ISDN line is up (Layer 2 Status 
should include: State = MULTIPLE_FRAME_ESTABLISHED )
"debug isdn q931" is your friend ;-)  As far as I'm concerned, this 
debug command has by far the most readable output of all Cisco IOS 
debugs :-)

regards,
  Zoltan

Erick Bergquist wrote:
> If you do a 'show isdn stat' on the router with PRI, does it say MULTI
> FRAME ESTABLISHED?
>
> If so, when you call the DIDs coming in on the new PRI, does 'debug
> isdn q931' show the call coming in?
>
>
> On Mon, Jul 7, 2008 at 11:44 PM, Leslie Meade <lmeade at signal.ca> wrote:
>   
>> I might of explained it wrong. I have a 4 port FSO with 4 inbound lines
>> that are all 1700.
>> I have a fractional PRI that has a pilot number of 1700 that is not
>> live, however the DiD's (that no one will use) are live.
>>
>> Once the go ahead is given the Telco will move the 1700 from the FXO to
>> the PRI as its pilot number. At this time I get fast busy on the PRI
>> DID's. Is this normal or is my config incorrect?
>>
>>
>>
>> -----Original Message-----
>> From: Jonathan Charles [mailto:jonvoip at gmail.com]
>> Sent: Monday, July 07, 2008 9:33 PM
>> To: Leslie Meade
>> Cc: cisco-voip at puck.nether.net
>> Subject: Re: [cisco-voip] cme/PRI newbie question
>>
>> Well, they have made the pilot live, but it isn't hunting to the other
>> FXO ports... so, once it is busy, the other calls fail. Open a ticket
>> with telco and tell them they are broken.
>>
>>
>> Jonathan
>>
>> On Mon, Jul 7, 2008 at 11:23 PM, Leslie Meade <lmeade at signal.ca> wrote:
>>     
>>> I have a four port FXO card and a new fractional pri. The FXO has a
>>>       
>> four
>>     
>>> line over lay of XXX XXXX 1700 that is being ported to my pri as the
>>>       
>> pilot
>>     
>>> number.
>>>
>>>
>>>
>>> My question, when I make an inbound call with one of the new DID's.
>>>       
>> The
>>     
>>> phone rings and I get through. But if I try it again with another
>>>       
>> phone to
>>     
>>> the same number, while till on the first call I get busy signals. I
>>>       
>> have 15
>>     
>>> phones all with have the same config as the one below. I have been
>>>       
>> told that
>>     
>>> when the pilot number has been made live I will not have this issue. I
>>>       
>> this
>>     
>>> true or am I missing something in my config to allow multiple calls to
>>>       
>> the
>>     
>>> same number?
>>>
>>> None of the DID's in the PRI will be used only the 1700 (pilot number)
>>>       
>> is
>>     
>>> being used for incoming calls.
>>>
>>>
>>>
>>> Leslie
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> cisco-voip mailing list
>>> cisco-voip at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>
>>>
>>>       
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>>     
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>