[cisco-voip] did/fxs config help

[Dan Letkeman]

Yes, this is a working CCME deployment.  Everything else is working
already just not the incoming DID calls on the VIC2-4FXS/DID card.

I have all of the ephone-dn's and ephones configured.

Dan.

On Wed, Jul 23, 2008 at 6:53 PM, Paul <asobihoudai at yahoo.com> wrote:
> Dan,
>
> Are you using IP phones? This is a CCME deployment correct?
>
> If so you need to setup ephones and ephone-DNs.
>
> Paul
>
>
>
> ----- Original Message ----
> From: Dan Letkeman <danletkeman at gmail.com>
> To: Paul <asobihoudai at yahoo.com>; cisco-voip at puck.nether.net
> Sent: Wednesday, July 23, 2008 4:44:33 PM
> Subject: Re: [cisco-voip] did/fxs config help
>
> Ok, so this is what I have so far, but I still get a busy signal.
>
> voice-port 0/1/0
> signal did wink-start
> input gain 4
>
>
> dial-peer voice 150 pots
> incoming called-number 5552340
> port 0/1/0
> !
> !
> num-exp 2340 1010
>
> You were saying something about an ephone-dn?
>
> Dan.
>
> On Wed, Jul 23, 2008 at 5:39 PM, Paul <asobihoudai at yahoo.com> wrote:
>> Dan,
>>
>> What you need is to configure a dial-peer with 'incoming called-number .' and configure your ephone-DNs. Every created ephone-DN creates a virtual dial-peer that is associated with the ephone that you assign this ephone-DN to.
>>
>> Paul
>>
>>
>>
>> ----- Original Message ----
>> From: Dan Letkeman <danletkeman at gmail.com>
>> To: Craig Staffin <craig at staffin.org>; cisco-voip at puck.nether.net
>> Sent: Wednesday, July 23, 2008 3:06:58 PM
>> Subject: Re: [cisco-voip] did/fxs config help
>>
>> Ok.  I think I need to configure both the dial peer's and the
>> called-number.  Do you have an example config or some links to
>> configure this?
>>
>> Thanks,
>> Dan.
>>
>> On Wed, Jul 23, 2008 at 6:46 AM, Craig Staffin <craig at staffin.org> wrote:
>>> Moataz,
>>> Not always true the FXS ports are actually used for analog DID trunks.
>>> As far as the problem do you have dial peers on the router?  You will need
>>> both an inacoming dial peer and outgoing OR  a phone with that DN on it
>>> THe incoming must have incoming-called-number . (or some form of the number)
>>> Craig
>>>
>>> On Wed, Jul 23, 2008 at 4:43 AM, Moataz Mamdouh <moataz_mmdh at yahoo.com>
>>> wrote:
>>>>
>>>> u call from FXS!!!!
>>>> --- On Tue, 7/22/08, Dan Letkeman <danletkeman at gmail.com> wrote:
>>>>
>>>> From: Dan Letkeman <danletkeman at gmail.com>
>>>> Subject: [cisco-voip] did/fxs config help
>>>> To: cisco-voip at puck.nether.net
>>>> Date: Tuesday, July 22, 2008, 9:51 PM
>>>>
>>>> Hello,
>>>>
>>>> I'm trying to setup a couple of did lines into a cme router.
>>>> Currently the voice ports look like this:
>>>>
>>>> voice-port 0/1/1
>>>>  signal did wink-start
>>>>
>>>>  input gain 4
>>>>
>>>> and I have setup the num-exp commands:
>>>>
>>>> num-exp 2346 1002
>>>> num-exp 2341 1011
>>>> num-exp 2347 1020
>>>>
>>>> I'm guessing I need a dial-peer?
>>>>
>>>> When I call the number 5552340 all I get is a busy signal.
>>>>
>>>>
>>>> Where should I go from
>>>>  here?
>>>>
>>>> Thanks,
>>>> Dan.
>>>> _______________________________________________
>>>> cisco-voip mailing list
>>>> cisco-voip at puck.nether.net
>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>>
>>>> _______________________________________________
>>>> cisco-voip mailing list
>>>> cisco-voip at puck.nether.net
>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>>
>>>
>>>
>>>
>>> --
>>> Craig Staffin
>>> Craig at staffin.org
>>> (H) 262-437-7313
>>> (C) 262-613-6003
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>>
>>
>>
>
>
>
>
>