[cisco-voip] Outbound Dial with Carrier SIP Trunk

[Wilusz, Mike]

Ryan,

 

There's no required authentication for the provider (username/password).
The show command just shows empty.

 

Thanks everyone for the input so far in case I forgot to say that!

 

Mike Wilusz, CCNA

Networking Systems Programmer

Price Chopper Supermarkets / The Golub Corporation

From: Ryan West [mailto:rwest at zyedge.com] 
Sent: Thursday, October 02, 2008 4:17 PM
To: Wilusz, Mike; Matt Slaga (US); cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Outbound Dial with Carrier SIP Trunk

 

Are you required to register your sip-ua?  If so, please also post 'show
sip-ua reg stat'

 

-ryan

 

From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Wilusz, Mike
Sent: Thursday, October 02, 2008 4:11 PM
To: Matt Slaga (US); cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Outbound Dial with Carrier SIP Trunk

 

Matt,

 

Tried that and I still get the same result.  The voice config from the
CUBE is this:

 

voice service voip

 address-hiding

 allow-connections h323 to h323

 allow-connections h323 to sip

 allow-connections sip to h323

 allow-connections sip to sip

!

dial-peer voice 2 voip

 destination-pattern 1..........

 session protocol sipv2

 session target ipv4:64.206.114.6 (Carrier Gateway)

 dtmf-relay rtp-nte

 codec g711ulaw

!

dial-peer voice 3 voip

 destination-pattern 3474179896

 session protocol sipv2

 session target ipv4:10.50.120.33 (Our CUCM)

 dtmf-relay rtp-nte

 codec g711ulaw

!

!

sip-ua

 registrar ipv4:64.206.114.6 expires 3600

 

 

Mike Wilusz, CCNA

Networking Systems Programmer

Price Chopper Supermarkets / The Golub Corporation

 

From: Matt Slaga (US) [mailto:Matt.Slaga at us.didata.com] 
Sent: Thursday, October 02, 2008 4:06 PM
To: Wilusz, Mike; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Outbound Dial with Carrier SIP Trunk

 

Try adding this to your config:

 

voice class codec 1

 codec preference 1 g711ulaw

 codec preference 2 g729br8

 codec preference 3 g729r8

 

 

And to your voip dial peers:

 

voice-class codec 1

 

 

 

 

From: Wilusz, Mike [mailto:mikewilusz at pricechopper.com] 
Sent: Thursday, October 02, 2008 3:42 PM
To: Matt Slaga (US); cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Outbound Dial with Carrier SIP Trunk

 

Yup... set here in this dial-peer.  Which is matched properly according
to the debug.

 

dial-peer voice 2 voip

 destination-pattern 1..........

 session protocol sipv2

 session target ipv4:64.206.114.6

 dtmf-relay rtp-nte

 codec g711ulaw

 

 

Mike Wilusz, CCNA

Networking Systems Programmer

Price Chopper Supermarkets / The Golub Corporation

 

From: Matt Slaga (US) [mailto:Matt.Slaga at us.didata.com] 
Sent: Thursday, October 02, 2008 3:40 PM
To: Wilusz, Mike; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Outbound Dial with Carrier SIP Trunk

 

Where are you setting the codec?  The line below says you are not using
VCC, are your dial peers specifying a codec?

 

Oct  2 10:21:18: //10/36ECCAF0801A/SIP/Info/sipSPIGetCallConfig: Not
using Voice Class Codec

 

 

 

 

From: Wilusz, Mike [mailto:mikewilusz at pricechopper.com] 
Sent: Thursday, October 02, 2008 3:35 PM
To: Matt Slaga (US); cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Outbound Dial with Carrier SIP Trunk

 

Matt,

 

Not sure what means.  I see g726r32 is selected as a codec...but why?  I
don't have the set as my codec on the dial-peer and the carrier is set
(or supposed to be) to the same as me.  I guess I'm not really sure what
that line is telling me.

 

Mike Wilusz, CCNA

Networking Systems Programmer

Price Chopper Supermarkets / The Golub Corporation

 

From: Matt Slaga (US) [mailto:Matt.Slaga at us.didata.com] 
Sent: Thursday, October 02, 2008 3:14 PM
To: Wilusz, Mike; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Outbound Dial with Carrier SIP Trunk

 

Probably this:

 

 

Oct  2 10:21:18: //9/36ECCAF0801A/SIP/Info/sipSPISelectDynamicPayload:
Selecting Dynamic Payload : 96 for Codec: g726r32

 

 

 

From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Wilusz, Mike
Sent: Thursday, October 02, 2008 10:31 AM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] Outbound Dial with Carrier SIP Trunk

 

Hey All,

 

We're in the process of trialing a SIP trunk solution from our provider,
PAETEC.  I followed the Cisco docs for configuring a CUBE, but we can
only receive calls and not place them.  The setup is CUCM 6.1(2) -> SIP
Trunk -> CUBE (2811) -> SIP Trunk -> PAETEC SIP Gateway.  I'm very new
to SIP and am trying to analyze the output from debug ccsip all.
Nothing is jumping out at me as the exact reason why the calls outbound
from our CUCM aren't working.  Anybody have any ideas?

 

 

________________________________

Disclaimer: This e-mail communication and any attachments may contain
confidential and privileged information and is for use by the designated
addressee(s) named above only. If you are not the intended addressee,
you are hereby notified that you have received this communication in
error and that any use or reproduction of this email or its contents is
strictly prohibited and may be unlawful. If you have received this
communication in error, please notify us immediately by replying to this
message and deleting it from your computer. Thank you. 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20081002/527d7561/attachment.html>