[cisco-voip] MGCP tranlsation rules

Ryan Ratliff rratliff at cisco.com
Thu Oct 30 12:31:10 EDT 2008


It is possible using translation patterns but the translation patterns can
only be matched using the called party number, not the calling number.   


-Ryan 
-----Original Message-----
From: Nemanja Stosic [mailto:nemanja.stosic at finsoft.rs] 
Sent: Thursday, October 30, 2008 12:23 PM
To: 'Ryan Ratliff'; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] MGCP tranlsation rules

Yes, that's right I want to change calling party number for inbound calls
from an MGCP endpoint :) That's not possible with MGCP endpoint?


Regs Nemanja

-----Original Message-----
From: Ryan Ratliff [mailto:rratliff at cisco.com]
Sent: Thursday, October 30, 2008 5:16 PM
To: 'Nemanja Stosic'; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] MGCP tranlsation rules

Sorry I think I misread  your problem.  You want to change the calling party
number for inbound calls from an MGCP endpoint?

Since CUCM cannot route based on calling party number you can apply only a
single translation pattern for all calls from the gateway.  I think this is
what you were getting at in your last email.

I don't think you can achieve what you are talking about with MGCP.


-Ryan
-----Original Message-----
From: Nemanja Stosic [mailto:nemanja.stosic at finsoft.rs]
Sent: Thursday, October 30, 2008 11:50 AM
To: 'Ryan Ratliff'; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] MGCP tranlsation rules

But I can create only one Translation CSS which is bounded to voice gateway
ISDN wic's? Then I can create route pattern which is going to remove 9011,
and dial out?

-----Original Message-----
From: Ryan Ratliff [mailto:rratliff at cisco.com]
Sent: Thursday, October 30, 2008 4:46 PM
To: 'Nemanja Stosic'; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] MGCP tranlsation rules

With H.323 you can do this easily using translation-rules.  With an MGCP
controlled endpoint the router passes on all digits to CUCM and you'll have
to do the same using translation patterns. 


-Ryan
-----Original Message-----
From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Nemanja Stosic
Sent: Thursday, October 30, 2008 11:06 AM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] MGCP tranlsation rules

Hi,
I am having a problem. When I receive a call, I have a caller ID in this
format 11xxxxx , 64xxxxx etc. I know that I can make translation rules on
CCM. But is there any way I can do that on Voice Gateway. I would like to,
when I receive a call 11xxxx, to remove 11 and replace it with 9 keeping all
the numbers behind 9, but when I receive a call 64xxxx, I just want to add
9. Is it possible to do it? I am using CCM 4.2 and voce gateway is 2801 with
3 ISDN BRI wic.

Thanks in advance 

Regs

Nemanja Stosic
System and Network administrator

GTECH Belgrade
Kosovska 51
11000 Belgrade
Serbia
Tel: +381 11 330  5789
Mob: +381 64 80 37 111

http://www.finsoft.rs

*******************************************************************
The information in this E-mail is  confidential. If you are not the intended
recipient please  notify the sender immediately and delete this E-mail
without reading, using or disseminating the information contained in it.

Although Finsoft Ltd  believes this E-mail and any  attachments are free of
any  virus or other  defect which may affect a computer, it is the
responsibility of the  recipient to ensure that it is virus free and Finsoft
Ltd  does not accept any  responsibility  for any loss or damage arising in
any way from its use.
*******************************************************************



_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip





More information about the cisco-voip mailing list