[cisco-voip] vg224 sccp config

[Lelio Fulgenzi]

The thought behind creating a dialpeer and activating stcapp for all ports is to eliminate the need to telnet into the vg224 each time you need to activate a port. For those of us with MAC desks, it's easier to have them simply add a DN to an existing and already configured vg224 port (device) then it is to have them telnet and create a dialpeer or have to wait until we do it.

ymmv

--------------------------------------------------------------------------------
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
"Bad grammar makes me [sic]" - Tshirt

  ----- Original Message ----- 
  From: Paul 
  To: Jason Aarons (US) ; Lelio Fulgenzi ; Joe Cisco 
  Cc: cisco-voip at puck.nether.net 
  Sent: Wednesday, September 24, 2008 2:22 AM
  Subject: Re: [cisco-voip] vg224 sccp config


  It's safe to say that if you should only activate stcapp on the ports you're going to use or they're constantly flood your CCM cluster with register attempts. Therefore only create stcapp dial peers for the ports you'll use.


  ----- Original Message ----
  From: Jason Aarons (US) <jason.aarons at us.didata.com>
  To: Lelio Fulgenzi <lelio at uoguelph.ca>; Joe Cisco <smetsysocsic at gmail.com>
  Cc: cisco-voip at puck.nether.net
  Sent: Wednesday, September 24, 2008 6:25:59 AM
  Subject: Re: [cisco-voip] vg224 sccp config


  Make sure you put a dn on all lines, else every vg224 port will try to autoregister filling up your log files if you have auto-register off -jason



  From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Lelio Fulgenzi
  Sent: Tuesday, September 23, 2008 4:33 PM
  To: Joe Cisco
  Cc: cisco-voip at puck.nether.net
  Subject: Re: [cisco-voip] vg224 sccp config



  I think it's important to give credit where credit is due....Ed Leatherman suggested the "configure all" approach....thanks Ed.


  ---
  Lelio Fulgenzi, B.A.
  Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
  (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  "Bad grammar makes me [sic]" - Tshirt


  ----- Original Message -----
  From: "Lelio Fulgenzi" <lelio at uoguelph.ca>
  To: "Joe Cisco" <smetsysocsic at gmail.com>
  Cc: cisco-voip at puck.nether.net
  Sent: Tuesday, September 23, 2008 2:46:44 PM GMT -05:00 US/Canada Eastern
  Subject: Re: [cisco-voip] vg224 sccp config

  Here's a quick snapshot. 

    a.. this is SCCP config only, i have not included ip config, routing, loopback, etc. 
    b.. consider enabling all ports using the STCAP command and configuring all ports in callmanager regardless of whether there is an extension/DN on it or not. 
    c.. by configuring all ports and never deleting them, only removing the DNs, you are able to manage things without having to connect to the gateway to add/remove dial peers. 



------------------------------------------------------------------------------

  !
  stcapp ccm-group <groupnum>
  stcapp
  !
  voice-card 0
  !
  !
  voice service voip
   modem passthrough nse codec g711ulaw
  !
  sccp ccm <ipaddr> identifier <idnum1>
  sccp ccm <ipaddr> identifier <idnum2>
  sccp
  !
  sccp ccm group <groupnum>
   associate ccm <idnum1> priority 1
   associate ccm <idnum2> priority 2
  !
  !
  dial-peer voice <dialpeer1> pots
   service stcapp
   port 2/0
  !
  dial-peer voice <dialpeer2> pots
   service stcapp
   port 2/1
  !


------------------------------------------------------------------------------




  ---
  Lelio Fulgenzi, B.A.
  Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
  (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  "Bad grammar makes me [sic]" - Tshirt


  ----- Original Message -----
  From: "Joe Cisco" <smetsysocsic at gmail.com>
  To: cisco-voip at puck.nether.net
  Sent: Tuesday, September 23, 2008 11:55:47 AM GMT -05:00 US/Canada Eastern
  Subject: [cisco-voip] vg224 sccp config

  Does anyone have an example IOS sccp config for a vg224? I've never
  built any type of router as sccp, always been an mgcp kind of guy, but
  we want some of the advanced analog functionality sccp provides. Any
  tips/tricks anyone's learned or gotchas i need to be aware of?

  Joe C.
  _______________________________________________
  cisco-voip mailing list
  cisco-voip at puck.nether.net
  https://puck.nether.net/mailman/listinfo/cisco-voip


  _______________________________________________ cisco-voip mailing list cisco-voip at puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-voip 



------------------------------------------------------------------------------


  Disclaimer: This e-mail communication and any attachments may contain confidential and privileged information and is for use by the designated addressee(s) named above only. If you are not the intended addressee, you are hereby notified that you have received this communication in error and that any use or reproduction of this email or its contents is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by replying to this message and deleting it from your computer. Thank you. 


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20080924/8ec10320/attachment.html>