[cisco-voip] Cisco 2801 - PRI

[Syed Khalid Ali]

Since you are using 2801, you must have ordered the voice bundle. It
has 1-PVDM8. I think you will needa minimum  PVDM 16 but should check
the dsp calculator for total number of DSPs required:

http://www.cisco.com/cgi-bin/Support/DSP/cisco_prodsel.pl

On Thu, Jul 2, 2009 at 7:56 AM, Mike Thompson<mthompson729 at gmail.com> wrote:
> Unfortunately you don’t have enough PVDM channels.
>
>
>
> In order to fire up a PRI, you need that PVDM to be at least 24 channels
> (the one here is only 8).  You would have to pull this one and put in a
> PVDM2-32 to be able to accomplish what you need.
>
>
>
> MT
>
>
>
> From: Jeffrey S. McNeal [mailto:jmcneal at vtg.biz]
> Sent: Wednesday, July 01, 2009 10:49 PM
> To: Mike Thompson
> Subject: RE: [cisco-voip] Cisco 2801 - PRI
>
>
>
> Is this what you are talking about
>
>
>
>  PVDM Slot 0:
>  8-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
>  Hardware Revision        : 3.2
>  Part Number              : 73-8848-04
>  Board Revision           : A0
>  Deviation Number         : 0
>  Fab Version              : 03
>  PCB Serial Number        : FOC091229KT
>  RMA Test History         : 00
>  RMA Number               : 0-0-0-0
>  RMA History              : 00
>  Processor type           : 00
>  Product (FRU) Number     : PVDM2-8
>  Version Identifier       : NA
>  EEPROM format version 4
>  EEPROM contents (hex):
>    0x00: 04 FF 40 04 30 41 03 02 82 49 22 90 04 42 41 30
>    0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 30 39 31 32
>    0x20: 32 39 4B 54 03 00 81 00 00 00 00 04 00 09 00 CB
>    0x30: 87 50 56 44 4D 32 2D 38 89 4E 41 20 20 D9 02 40
>    0x40: C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
>    0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
>    0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
>    0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
>
>
>
>
>
> ________________________________
>
> From: Mike Thompson [mailto:mthompson729 at gmail.com]
> Sent: Wed 7/1/2009 10:47 PM
> To: Jeffrey S. McNeal
> Subject: RE: [cisco-voip] Cisco 2801 - PRI
>
> What do you get from the show diag.
>
>
>
> From: Jeffrey S. McNeal [mailto:jmcneal at vtg.biz]
> Sent: Wednesday, July 01, 2009 10:31 PM
> To: Mike Thompson; cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] Cisco 2801 - PRI
>
>
>
> There is only 1 PRI.  I have a 2 T1 card 1 for a metro t1 and then the other
> I was going to use for the PRI.
>
>
>
> Jeffrey S. McNeal
>
> Vision Technology Group, LLC
>
> 125 West Bruce Street
>
> Harrisonburg, VA 22801
>
> (540) 437-0112 - Office
>
> (540) 437-0129 - Fax
>
>
>
>
>
> ________________________________
>
> From: Mike Thompson [mailto:mthompson729 at gmail.com]
> Sent: Wed 7/1/2009 10:25 PM
> To: Jeffrey S. McNeal; cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] Cisco 2801 - PRI
>
> Need to have PVDM2-XX (need 24 total channels total channels: type show diag
> and look for PVDM, add em up and you’ll get the total).
>
>
>
> Keep in mind that a 2801 only supports a TOTAL of 30 PVDM channels.
>
>
>
> 2801 only supports 1 PRI, so if this isn’t the first one, that’s the issue.
>
>
>
> Have to have ISDN switch type set first
>
>
>
> Let me know what you get.
>
>
>
>
>
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Jeffrey S. McNeal
> Sent: Wednesday, July 01, 2009 10:17 PM
> To: cisco-voip at puck.nether.net
> Subject: [cisco-voip] Cisco 2801 - PRI
>
>
>
> Hello All,
>
>
>
> I am trying to configure a pri on a cisco 2801 but I get the following
> message:
>
>
>
> (config-controller)#pri-group timeslots 1-24
> % Not enough DSP resources available to configure pri-group on controller T1
> 0/1
> /1
> % The remaining dsp resources are enough for 4 time slots.
> % For current codec complexity, 2 extra dsp(s) are required to create this
> voice
>  port.
>
>
>
> Can I fix it or is something wrong?
>
>
>
>
>
> Jeffrey S. McNeal
>
> Vision Technology Group, LLC
>
> 125 West Bruce Street
>
> Harrisonburg, VA 22801
>
> (540) 437-0112 - Office
>
> (540) 437-0129 - Fax
>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>



-- 
Thanks,
Syed Khalid Ali