[cisco-voip] Conference Bridging Issues - 6509 with CMM-ACT
Dane
dane at pktloss.net
Mon Jul 13 13:21:47 EDT 2009
Your just referring to the "Find and List Conference Bridges Page" right?
It shows the "status" as being the subscriber CM. When you click on a
conf. bridge device you see "Registration: Registered with Cisco
CallManager 10.61.100.71" which is the subscriber.
Hope I am understanding you correctly. If there is someplace else I
should be looking please let me know.
thanks!
On Mon, Jul 13, 2009 at 12:14 PM, Philip Walenta<pwalenta at wi.rr.com> wrote:
> One very basic question - in the conference device list do you see your
> CMM's registered?
>
> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Dane
> Sent: Monday, July 13, 2009 12:03 PM
> To: cisco-voip at puck.nether.net
> Subject: [cisco-voip] Conference Bridging Issues - 6509 with CMM-ACT
>
> Having some trouble getting the conference bridging moved over to the CMM's
> in my 6509s. CallManager is running 4.1(3)
>
> I thought I setup everything correctly but adhoc conferencing from phones
> isn't working.
>
> I guess the first question I have is to make sure I am not confusing things.
> The conferencing I am attempting is from my 7960. I call one user, press
> the confrn softkey on phone and it places user on hold and provides me
> dialtone to call another user. I do that and other user picks up and I then
> hit confrn. softkey one more time.
>
> When I do that it hangs up on both users and says "Can Not Join Calls".
>
> I think I had three basic things I needed to do in order to get these
> CMM-ACT's working.
>
> 1. Configure the CMM IOS side to support the conference bridging 2. Add the
> new conference bridges in CallManager (also removed the old ones point to
> 6608s) 3. Add the new conference bridge media resources to the existing
> media resource group and remove the old ones.
>
> All of these steps were done but obviously I either did something
> incorrectly or I am missing something.
>
> Here is my config on the CMM:
>
>
> mediacard 3
> resource-pool conf_bridging dsps 2
> !
> !
> sccp local GigabitEthernet1/0
> sccp ccm 10.61.100.71 identifier 2 version 4.1 sccp ccm 10.61.100.70
> identifier 1 version 4.1 sccp !
> sccp ccm group 1
> bind interface GigabitEthernet1/0
> associate ccm 1 priority 2
> associate ccm 2 priority 1
> associate profile 1 register C05001a6c0368d6 !
> dspfarm
> !
> dspfarm profile 1 conference adhoc
> rtp timeout 600
> codec g711ulaw packetization-period 30
> codec g711alaw packetization-period 30
> codec g729r8 packetization-period 30
> codec g729ar8 packetization-period 30
> codec g723r63 packetization-period 30
> codec g723r53 packetization-period 30
> vad override off
> associate resource-pool conf_bridging
>
>
>
> On CallManager I added the conference bridge as follows and it does show as
> registered:
>
> Type: Cisco Conference Bridge (WS-SVC-CMM)
> Name: C05001A6C0368D6
> MAC: 001A6C0368D6
> Subunit: 3
> Max Capacity: 32 ---> This was default, doesn't 1 dsp handle 32?
> Resource pool shows 2 dsps, matter?
> RTP Timeout: 600
>
>
> Appreciate any thoughts or suggestions about this.
>
> Regards,
> Dane
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
More information about the cisco-voip
mailing list