[cisco-voip] VIC2-1MFT-G703 and VIC2-1MFT-T1/E1

[Syed Khalid Ali]

No G703 card still need a modem. What I understood that in case of T1
there is no need of an external CSU/DSU. with E1 it still requires an
E1 modem

By unframed means that the whole 2.04mb can be used; that is all time
slots are available.

G703 are not EOS/EOL

On Fri, Jul 24, 2009 at 2:17 PM, Moataz Mamdouh<moataz_mmdh at yahoo.com> wrote:
>
> so u mean that G.703 card doesn 't need a modem , the Teleco Cable will be
> directly connected to the router.
>
> what do u mean about unframed ? u don't have the time slot command under the
> controller !!!
> i can't see any difference between both cards ( is G.703 card are EOS ? ) as
> they are supported only on 26xx and 36xx not ISR.
>
> --- On Fri, 7/24/09, Syed Khalid Ali <syed.khalid.khursheed at gmail.com>
> wrote:
>
> From: Syed Khalid Ali <syed.khalid.khursheed at gmail.com>
> Subject: Re: [cisco-voip] VIC2-1MFT-G703 and VIC2-1MFT-T1/E1
> To: "Moataz Mamdouh" <moataz_mmdh at yahoo.com>, cisco-voip at puck.nether.net
> Date: Friday, July 24, 2009, 5:07 AM
>
> After reading the data sheets I was able to put out theses
> differences. Can any one validate!
>
> MFT-T1/E1 does framed E1 (31 timeslots @ 64 Kbps) and fractional (n<31
> timeslots @ 64 Kbps) and T1 support.
> MFT-G703 additionally does unframed (2048 Kbps) and no T1 support.
> Both support the dedicated echo cancellation daughter module EC-MFT-32 or
> 64.
> With MFT-T1/E1 there is no need for external CSU/DSU when used as a T1
> module.
> Drop and Insert capability.
> Supported in 1841 and higher ISR series routers.
> Supported with 2600, 2600XM, 2691, 3660, 3700 and higher models.
>
> The NM-xCE1T1-PRI does not support dedicated echo-cancellation card.
> Supports with framed and unframed E1 signaling no need for another G.703
> card.
> No Multiflex operation.
> Compatible with supported V.92 modems.
> Supports (native) termination of balanced (coaxial) cable.
> Simultaneous support of T1 and E1 operation on the same NM-module.
> Supported in 2600XM and onwards.
> Online insertion and removal (OIR) supported on Cisco 3660, 3745 and
> 3845 routers.
> On-board expansion slot for future usage.
>
> One thing that still confuses me that in case of VWIC2-2MFT-T1/E1 can
> one port act as a T1 and other as E1.
>
> Any other thing that someone wants to add!!!
>
>
>
> On Fri, Jul 24, 2009 at 1:49 PM, Moataz Mamdouh<moataz_mmdh at yahoo.com>
> wrote:
>> I am not sure but i think they are the same , because G.703 is ITU
>> standard
>> for voice and data over T1 and E1
>>
>>
>> --- On Thu, 7/23/09, Syed Khalid Ali <syed.khalid.khursheed at gmail.com>
>> wrote:
>>
>> From: Syed Khalid Ali <syed.khalid.khursheed at gmail.com>
>> Subject: [cisco-voip] VIC2-1MFT-G703 and VIC2-1MFT-T1/E1
>> To: cisco-voip at puck.nether.net
>> Date: Thursday, July 23, 2009, 12:59 PM
>>
>> what is the difference between G.703 and T1/E1 card beside support for
>> T1 in later one?
>> Also how can we compare these with NM-1CE1T1-PR. any thing special to
>> consider before going to ordering???
>>
>> --
>> Thanks,
>> Syed Khalid Ali
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>
>
>
> --
> Thanks,
> Syed Khalid Ali
>
>



-- 
Thanks,
Syed Khalid Ali