[cisco-voip] Help with first time VOIP setup.

Wed Jun 17 11:34:57 EDT 2009

I can't find any documentation on setting this up. Is it something thats 
supported on the 1760 with CME 4.1?

If not, do I have any options?

Thanks,

-Tony

Chris Ward (chrward) wrote:
> I think a hunt group in broadcast mode might be able to do it, but the lines wouldn't be shared lines...
> 
> -Chris
> 
> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Anthony R. Mattke
> Sent: Wednesday, June 17, 2009 9:39 AM
> To: Paul
> Cc: cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] Help with first time VOIP setup.
> 
> Without using sccp for my fxs, is there another way to accomplish my goal?
> 
> Basicly I'm going to have 2 lines coming in on FXO ports. One of them is 
> the home line, one is my office line. I would like to be able to answer 
> either of them on my 7960. But also ring the FXS port when calls come in 
>   on the home line.
> 
> Thanks again for all the help..
> 
> -T
> 
> Paul wrote:
>> Doh. You can't use SCCP to control your FXS port then...an ATA in this case would come in handy to use a device connected to its FXS port but that isn't the point in this case. . . 
>>
>>
>> ----- Original Message ----
>> From: Anthony R. Mattke <a.mattke at gmail.com>
>> To: Paul <asobihoudai at yahoo.com>
>> Cc: cisco-voip at puck.nether.net
>> Sent: Wednesday, June 17, 2009 12:35:24 AM
>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>
>> I just found this as well..
>>
>> http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxsfeatmd.html#wp1108210
>>
>> So, this is maybe not supported on the 1760 ???
>>
>> Is there another method I could use to ring the FXS port at the same time as the ephone-dn ???
>>
>> -Tony
>>> Anthony R. Mattke wrote:
>>>> Well, I found the service on this page.
>>>> http://uc500.com/using-stcapp-make-fxs-port-sccp-phone
>>>>
>>>> which takes you to this page on Cisco's website.
>>>>
>>>> http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxssccpsplmft.html 
>>>>
>>>> There I see
>>>> Prerequisites for SCCP Controlled Analog (FXS) Ports with Supplementary Features in Cisco IOS Gateways
>>>>
>>>> Cisco IOS Gateway
>>>>
>>>> •Cisco IOS Release 12.3(11)T or a later release.
>>>> --- I'm running 12.4(15)T7 Voice9-M
>>>>
>>>> •The Cisco voice gateway is set up and configured for operation. For information, see the appropriate Cisco configuration documentation.
>>>>
>>>>
>>>> •The analog FXS voice ports are set up and configured for operation. For information, see the Cisco IOS Voice Port Configuration Guide.
>>>>
>>>>
>>>> •SCCP and the SCCP telephony control (STC) application is enabled on the Cisco voice gateway. For configuration information, see "Configuring FXS Ports for Basic Calls" on page 25.
>>>>
>>>>
>>>> Tne rest of these seem fine, yet I have no STCAPP
>>>>
>>>> -Tony
>>>>
>>>> Paul wrote:
>>>>> I could be wrong, but I'm pretty sure the document referencing this ability states the version of IOS and possibly rooter required.
>>>>>
>>>>>
>>>>> ----- Original Message ----
>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>> To: Paul <asobihoudai at yahoo.com>
>>>>> Cc: cisco-voip at puck.nether.net
>>>>> Sent: Tuesday, June 16, 2009 10:40:02 PM
>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>>
>>>>> Yeah, I think I found what I"m looking for.. but I need to do some more research, as my IOS or router isn't supporting what I found..
>>>>>
>>>>> It shows setting up something such as the following.
>>>>>
>>>>> !
>>>>> dial-peer voice 55 pots
>>>>> service stcapp
>>>>> port 1/1
>>>>> !
>>>>> voice-port 1/1
>>>>> caller-id enable
>>>>> !
>>>>> ephone 10
>>>>> device-security-mode none
>>>>> mac-address DA2F.E2B0.0001
>>>>> type anl
>>>>> button 1:5
>>>>> !
>>>>>
>>>>>
>>>>> I stcapp isn't shown on the service options list, but it lets me enter it. Altho when I try ot get the mac address from show stcapp device summary -- that command is missing..
>>>>>
>>>>> Can't seem to find much on the Cisco FN on this topic.. is this a device limitation, or is it IOS based?
>>>>>
>>>>> -Tony
>>>>>
>>>>>
>>>>> Paul wrote:
>>>>>> search for fxs sccp controlled or something like that...
>>>>>>
>>>>>>
>>>>>> ----- Original Message ----
>>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>>> To: Paul <asobihoudai at yahoo.com>
>>>>>> Cc: cisco-voip at puck.nether.net
>>>>>> Sent: Tuesday, June 16, 2009 10:19:29 PM
>>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>>>
>>>>>> I had no clue you could do that.. Sorry ! I'll look and see if I find an example of that done.
>>>>>>
>>>>>> Thanks !
>>>>>>
>>>>>> -Tony
>>>>>>
>>>>>>
>>>>>> Paul wrote:
>>>>>>> Then make it an ephone by registering your FXS port using SCCP.
>>>>>>>
>>>>>>> It's easier that way...
>>>>>>>
>>>>>>>
>>>>>>> ----- Original Message ----
>>>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>>>> To: Paul <asobihoudai at yahoo.com>
>>>>>>> Cc: cisco-voip at puck.nether.net
>>>>>>> Sent: Tuesday, June 16, 2009 10:12:37 PM
>>>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>>>>
>>>>>>> One of them isn't an ephone. Its a FXS port using a dial-peer such as..
>>>>>>>
>>>>>>> !
>>>>>>> dial-peer voice 55 pots
>>>>>>> destination-pattern 55
>>>>>>> port 1/1
>>>>>>> !
>>>>>>>
>>>>>>> And then a ephone-dn that I want to use the same extension, or make ring at the same time so either can answer the call..
>>>>>>>
>>>>>>> Paul wrote:
>>>>>>>> Use overlay.
>>>>>>>>
>>>>>>>> Assign ephone one and two the same extension originating from two separate ephone-DNs and then use overlay to have them both ring.
>>>>>>>>
>>>>>>>>
>>>>>>>> ----- Original Message ----
>>>>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>>>>> To: cisco-voip at puck.nether.net
>>>>>>>> Sent: Tuesday, June 16, 2009 6:13:32 PM
>>>>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>>>>>
>>>>>>>> Ok, so today, I've been attempting to have two phones ring for the same extension.
>>>>>>>>
>>>>>>>> I see this is fairly simple if they're both ephones, but what about 1 ephone and 1 pots ? I can't seem to make this work, and I can't find any documentation regarding setting this up.
>>>>>>>>
>>>>>>>> -Tony
>>>>>>>> _______________________________________________
>>>>>>>> cisco-voip mailing list
>>>>>>>> cisco-voip at puck.nether.net
>>>>>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>      
>>>>>>>    
>>>>>>    
>>>>>      
>>>> _______________________________________________
>>>> cisco-voip mailing list
>>>> cisco-voip at puck.nether.net
>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>       
>>
> 
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip