[cisco-voip] ATA 186 for Elevator - Voltage

[Nick Matthews]

You may also want to look at the VIC3-2FXS-E/DID

These cards are the third generation VICs (E) that have higher voltage
capabilities specifically for things like elevator phones and fire
alarm panels.

The data sheet gives more specifics:
http://www.cisco.com/en/US/solutions/collateral/ns340/ns517/ns477/ns296/data_sheet_c78_464185_ns477_Networking_Solution_Solution_Overview.html


-nick

On Tue, May 12, 2009 at 12:59 PM, Bob Fronk <bob at btrfronk.com> wrote:
> Nice!... Just had an issue with a fire alarm system complaining about
> voltage on an FXO port.  This might be my answer.
>
>
>
> Bob Fronk
>
>
>
>
>
>
>
>
>
>
>
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Lelio Fulgenzi
> Sent: Tuesday, May 12, 2009 11:44 AM
> To: Mike Lydick
> Cc: cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] ATA 186 for Elevator - Voltage
>
>
>
> ooops, cut/paste didn't work properly:
>
> http://www.vikingelectronics.com/products/view_product.php?pid=294
>
> ---
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> "Bad grammar makes me [sic]" - Tshirt
>
>
> ----- Original Message -----
> From: "Lelio Fulgenzi" <lelio at uoguelph.ca>
> To: "Mike Lydick" <mike.lydick at gmail.com>
> Cc: cisco-voip at puck.nether.net
> Sent: Tuesday, May 12, 2009 11:37:23 AM GMT -05:00 US/Canada Eastern
> Subject: Re: [cisco-voip] ATA 186 for Elevator - Voltage
>
> http://www.vikingelectronics.com/products/search_cat_results.php?mycategory=
>
> you can add some voltage to the line.
>
> ---
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> "Bad grammar makes me [sic]" - Tshirt
>
>
> ----- Original Message -----
> From: "Mike Lydick" <mike.lydick at gmail.com>
> To: cisco-voip at puck.nether.net
> Sent: Tuesday, May 12, 2009 11:29:20 AM GMT -05:00 US/Canada Eastern
> Subject: [cisco-voip] ATA 186 for Elevator - Voltage
>
> We are being told that an ATA 186 will not supply enough voltage for an Otis
> Elevator Phone Control Board. Anyone have any experience with using an ATA
> for this purpose. The Elevator tech is asking for 53vdc to program the
> control board (they call and have the program signal sent back over the
> line). We have moved the ATA within 10' of the controller board (eliminate
> line driver issues). I have tried modifying FXSOutputLevel but this is only
> modifies the Gain? Any other options for boasting the line voltage for an
> ATA?
>
>
>
>
>
>
>
> Best Regards,
>
> Mike Lydick
>
>
> _______________________________________________ cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
> _______________________________________________ cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>