[cisco-voip] Router to Dial POTS line

[Jeff Ruttman]

I'm fairly new to the backend of CM and really new to routers, so that
explains many of your "Why would you...?" questions. :)

Maybe CM is the place to start; I just thought I would try dialing with
the router.  Dest-pattern is open so I can call other numbers.  I don't
want to chance calling 911 while I'm stumbling around.

I'll have a look at the CM side; I was just interested in learning how
to dial out with the router.  I suppose it is a CM problem though.

Thanks
jeff

-----Original Message-----
From: Paul [mailto:asobihoudai at yahoo.com] 
Sent: Thursday, May 14, 2009 1:37 PM
To: Jeff Ruttman; cisco-voip
Subject: Re: [cisco-voip] Router to Dial POTS line


What else have you tried? Are you sure the port is properly registered
to CCM? If you're only using it for 911 why would you set the dial-peer
up to dial anything under the sun? Use destination-pattern 911 or 9911.
If the port is registered, are you sure you put it in the correct CSS?




________________________________
From: Jeff Ruttman <ruttmanj at carewisc.org>
To: cisco-voip <cisco-voip at puck.nether.net>
Sent: Thursday, May 14, 2009 2:26:33 PM
Subject: [cisco-voip] Router to Dial POTS line


Greetings,
 
We have an analog line here which I'm setting up for
911 dialing.
 
The line itself works as I can call out with a buttset just
fine.  We have everything configured on the router and in Call Manager.
But
it doesn't work; we get a fast busy.  I want to see if my problem is
the router config or CM, so I'm trying to place a call from the router
thinking that would rule out the router config.
 
I've got the analog line plugged into the 0 port in
the FXO card.  I put "destination-pattern 9T" on the dial-peer
as it was part of some example I found in a cisco doc for dialing out
from a
router.  The rest of the configs match a config from another site.
 
voice-port 0/1/0
 timeouts call-disconnect 5
 timeouts wait-release 5
 timing hookflash-out 500
 description 911 Dialing
 
dial-peer voice 999010 pots
 service mgcpapp
 destination-pattern 9T
 port 0/1/0
 
Anyway, I get this when I place a call:
 
Router#csim start 95555555
csim: called number = 95555555, loop count = 1 ping count =
0
 
csim err:csim_do_test invalid major major(16) minor(0)
csim: loop = 1, failed = 0
csim: call attempted = 1, setup failed = 0, tone failed = 0
 
Any insight out there?
 
Thanks
jeff
 
 
 CONFIDENTIALITY NOTICE: The information contained in this email
including attachments is intended for the specific delivery to and use
by the individual(s) to whom it is addressed, and includes information
which should be considered as private and confidential. Any review,
retransmission, dissemination, or taking of any action in reliance upon
this information by anyone other than the intended recipient is
prohibited. If you have received this message in error, please reply to
the sender immediately and delete the original message and any copy of
it from your computer system. Thank you.


      

CONFIDENTIALITY NOTICE: The information contained in this email including attachments is intended for the specific delivery to and use by the individual(s) to whom it is addressed, and includes information which should be considered as private and confidential. Any review, retransmission, dissemination, or taking of any action in reliance upon this information by anyone other than the intended recipient is prohibited. If you have received this message in error, please reply to the sender immediately and delete the original message and any copy of it from your computer system. Thank you.