[cisco-voip] Best Test for New PRIs?

[Paul]

Testing through FXO ports could mean a number of different things...if you want to test calling your PRI circuits through your FXO ports, that might work...

It sounds like these PRI circuits are at another facility where you don't have ready access to setup a router and switch to them yet. Also PRI circuits aren't usually hot unless you ask TelCo to make them so. Your best test method will be with a console connection to the PRI-connected router on your lap, and a phone jammed betwixt your shoulder and head connected to TelCo requesting them to make the circuit hot for you to make test calls to your mobile phone or any other test handset you have available.


----- Original Message ----
From: "Miller, Steve" <MillerS at DicksteinShapiro.COM>
To: Erick Bergquist <erickbee at gmail.com>; ccieid1ot <ccieid1ot at gmail.com>
Cc: cisco-voip at puck.nether.net
Sent: Wednesday, May 20, 2009 8:55:40 AM
Subject: Re: [cisco-voip] Best Test for New PRIs?

Thanks for the suggestion.  We won't have any connectivity between offices. 

Will testing through FXO ports tell us anything about how the circuits will work with Call Manager? 


Steve Miller
Telecom Engineer
Dickstein Shapiro LLP
1825 Eye Street NW | Washington, DC 20006
Tel (202) 420-3370| Fax (202) 330-5607
MillerS at dicksteinshapiro.com 


-----Original Message-----
From: Erick Bergquist [mailto:erickbee at gmail.com] 
Sent: Tuesday, May 19, 2009 11:46 PM
To: ccieid1ot
Cc: Miller, Steve; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Best Test for New PRIs?

Does this gateway have network connectivity to the existing call
manager?  You could set it up in the CUCM before moving the servers
and test calls in/out that way. Set up the gateway and a test
partition, route patterns, CSSs and assign the test CSS to 1 or 2
phones.

If not, do like others have suggested previously in the discussion. If
you have a FXS port on the gateway you could test with a POTS phone
off the FXS port and dial peers.

On Tue, May 19, 2009 at 9:55 PM, ccieid1ot <ccieid1ot at gmail.com> wrote:
> Make yourself a T1 loopback plug if you don't have 2 VWIC cards.
>
> Wires for Crossover T1, 1-4 2-5.
>
> On Tue, May 19, 2009 at 2:58 PM, Miller, Steve
> <MillerS at dicksteinshapiro.com> wrote:
>> We will install a couple PRIs in a new office soon. We will be
>> moving/installing an existing CUCM 7.X system which currently exists at
>> another location (production), but it will already be move weekend when the
>> new equipment arrives and I want to be sure that the PRIs are working and
>> that the PRIs have been properly programmed for CUCM.
>>
>> Does anyone have details or testing plan for testing the PRIs before the
>> CUCM is installed?
>>
>> Is there any way to actually make calls with a 3825 router by hooking other
>> equipment to it?
>>
>> Is there a test set which would somehow emulate the system and allow us to
>> dial out and also receive calls on the circuit?
>>
>> Any ideas would be greatly appreciated!
>>
>>
>> Steve Miller
>> Telecom Engineer
>> Dickstein Shapiro LLP
>> 1825 Eye Street NW | Washington, DC 20006
>> Tel (202) 420-3370| Fax (202) 330-5607
>> MillerS at dicksteinshapiro.com
>>
>>
>>
>> --------------------------------------------------------
>> This e-mail message and any attached files are confidential and are intended
>> solely for the use of the addressee(s)
>> named above. This communication may contain material protected by
>> attorney-client, work product, or other
>> privileges. If you are not the intended recipient or person responsible for
>> delivering this confidential
>> communication to the intended recipient, you have received this
>> communication in error, and any review, use,
>> dissemination, forwarding, printing, copying, or other distribution of this
>> e-mail message and any attached files
>> is strictly prohibited. Dickstein Shapiro reserves the right to monitor any
>> communication that is created,
>> received, or sent on its network.  If you have received this confidential
>> communication in error, please notify the
>> sender immediately by reply e-mail message and permanently delete the
>> original message.
>> To reply to our email administrator directly, send an email to
>> postmaster at dicksteinshapiro.com
>> Dickstein Shapiro LLP
>> http://www.DicksteinShapiro.com
>> ==============================================================================
>>
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>


--------------------------------------------------------
This e-mail message and any attached files are confidential and are intended solely for the use of the addressee(s)
named above. This communication may contain material protected by attorney-client, work product, or other 
privileges. If you are not the intended recipient or person responsible for delivering this confidential
communication to the intended recipient, you have received this communication in error, and any review, use, 
dissemination, forwarding, printing, copying, or other distribution of this e-mail message and any attached files 
is strictly prohibited. Dickstein Shapiro reserves the right to monitor any communication that is created, 
received, or sent on its network.  If you have received this confidential communication in error, please notify the 
sender immediately by reply e-mail message and permanently delete the original message. 

To reply to our email administrator directly, send an email to postmaster at dicksteinshapiro.com

Dickstein Shapiro LLP
http://www.DicksteinShapiro.com

==============================================================================

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip