[cisco-voip] Wacky telco issues... cannot call the UK

[Jonathan Charles]

This fixed it... but why???

How was it getting tagged ISDN International in the first place???


Jonathan

On Mon, Nov 30, 2009 at 6:11 PM, Mike Taylor <mtaylor at employees.org> wrote:
> Does this help?
>
> !
> interface Serial0/0/0:15
>  no ip address
>  encapsulation hdlc
>  isdn switch-type primary-net5
>  isdn overlap-receiving
>  isdn incoming-voice voice
>  isdn map address .* plan unknown type unknown      <-------------
>
> Regards,
> Mike
>
> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Jonathan Charles
> Sent: Tuesday, 1 December 2009 12:59 p.m.
> To: Mike Lydick
> Cc: cisco-voip
> Subject: Re: [cisco-voip] Wacky telco issues... cannot call the UK
>
> Nope, it is an NI2... super duper confirmed...
>
>
> J
>
> On Mon, Nov 30, 2009 at 5:38 PM, Mike Lydick <mike.lydick at gmail.com> wrote:
>> I was thinking the same. Also does the provider require Software
>> Select features? Mega-com...
>>
>>
>> Best Regards,
>>
>> Mike Lydick
>>
>>
>>
>>
>> On Mon, Nov 30, 2009 at 6:30 PM, Scott Voll <svoll.voip at gmail.com> wrote:
>>>
>>> Can you leave it international and strip the 011?
>>>
>>>
>>> On Mon, Nov 30, 2009 at 3:16 PM, Jonathan Charles <jonvoip at gmail.com>
>>> wrote:
>>>>
>>>> OK, here's one that is stumping me...
>>>>
>>>> CUCM 7.0, H.323 Gateways with 3 PRIs.
>>>>
>>>> We can call all over Europe, Oceania, Asia... but not the UK.
>>>>
>>>> Calls go out:
>>>>
>>>> ch = primary-ni interface = User
>>>> Nov 30 17:07:21.704 CST: ISDN Se0/1/0:23 Q931: TX -> SETUP pd = 8
>>>> callref = 0x147B
>>>>        Bearer Capability i = 0x8090A2
>>>>                Standard = CCITT
>>>>                Transfer Capability = Speech
>>>>                Transfer Mode = Circuit
>>>>                Transfer Rate = 64 kbit/s
>>>>        Channel ID i = 0xA98397
>>>>                Exclusive, Channel 23
>>>>        Calling Party Number i = 0x2181, '8475552096'
>>>>                Plan:ISDN, Type:National
>>>>        Called Party Number i = 0x91, '011441787883195'
>>>>                Plan:ISDN, Type:International Nov 30 17:07:21.744
>>>> CST: ISDN Se0/1/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0x947B
>>>>        Channel ID i = 0xA98397
>>>>                Exclusive, Channel 23 MC003137# Nov 30 17:07:21.744
>>>> CST: ISDN Se0/1/0:23 Q931: RX <- PROGRESS pd = 8 callref = 0x947B
>>>>        Cause i = 0x829F - Normal, unspecified
>>>>
>>>>
>>>> And fail.
>>>>
>>>> On the Route Pattern, we are forcing plan and type to
>>>> unknown/unknown; telco came in and made these calls successfully
>>>> from the smartjacks; I have a dial peer invoking a translation profile:
>>>>
>>>>
>>>> !
>>>> voice translation-rule 2
>>>>  rule 1 // // type international unknown plan isdn unknown !
>>>> !voice translation-profile UK
>>>>  translate called 2
>>>> !
>>>>
>>>>
>>>> !
>>>> dial-peer voice 60 pots
>>>>  translation-profile outgoing UK
>>>>  destination-pattern 01144T
>>>>  port 0/0/0:23
>>>>  prefix 01144
>>>> !
>>>>
>>>> There are no transformation patterns on the system, there are no
>>>> translation patterns on the system; every other international call
>>>> succeeds without any issue (plan and type are unknown)...
>>>>
>>>>
>>>> Any ideas? I seriously have no idea where this plan and type are
>>>> coming from, or how to get rid of them...
>>>> _______________________________________________
>>>> cisco-voip mailing list
>>>> cisco-voip at puck.nether.net
>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>
>>>
>>> _______________________________________________
>>> cisco-voip mailing list
>>> cisco-voip at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>
>>
>>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>