[cisco-voip] PRI Trunk Group H323

Fri Sep 11 12:16:53 EDT 2009

These are from c3845-advipservicesk9-mz.124-11.XW3.bin, but I have another that is c3845-spservicesk9-mz.124-22.T1.bin, that is the same.

The annoying thing about trunk groups is there is 3 different syntaxes depending on the spot in ios

trunk group  InteCom  (defines the trunk group in global)
trunk-group InteCom 10 (on the voice port, or serial int)
trunkgroup InteCom (on the dial peer)

-Nate

-----Original Message-----
From: RAWLE GORDON [mailto:ragordon at mtb.com] 
Sent: Friday, September 11, 2009 10:12 AM
To: Jonathan Charles; Nate VanMaren
Cc: cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] PRI Trunk Group H323

Nate,
This option at the serial interface (Dchannel) for "trunk-group" is not available in IOS 12.4(20)X. What IOS is associated with these snips ?

TG

>>> Nate VanMaren <VanMarenNP at ldschurch.org> 9/11/2009 12:07 PM >>>
Nah, it's just the same as analog.

Here's a few snips of config and a show command.

trunk group  InteCom
 hunt-scheme sequential

interface Serial0/0/0:23
 trunk-group InteCom 10

interface Serial0/0/1:23
 trunk-group InteCom 11.

dial-peer voice 10 pots
 trunkgroup InteCom
 description InteCom PRIs Outbound
 translation-profile outgoing ToInteCom
 destination-pattern 0#*T

CHQVG001#sh trunk group InteCom
Trunk group: InteCom
        Description: 
        trunk group label: InteCom

        Translation profile (Incoming): 
        Translation profile (Outgoing): 

        Preemption is disabled

        Hunt Scheme is sequential
        Max Calls (Incoming):   NOT-SET (Any)   NOT-SET (Voice) NOT-SET (Data)
        Max Calls (Outgoing):   NOT-SET (Any)   NOT-SET (Voice) NOT-SET (Data)
        Max Calls (MixTotal):   NOT-SET (Any)   NOT-SET (Voice) NOT-SET (Data)
        Retries: 0

        Trunk Se0/0/0:23        Preference 10
                Member Timeslots : 1-24
                Total channels available : 23
                Data = 0, Voice = 2, Modem = 0, Pending = 0, Free = 21
        Trunk Se0/0/1:23        Preference 11
                Member Timeslots : 1-24
                Total channels available : 23
                Data = 0, Voice = 18, Modem = 0, Pending = 0, Free = 5
        Trunk Se0/1/0:23        Preference 12
                Member Timeslots : 1-24
                Total channels available : 23
                Data = 0, Voice = 20, Modem = 0, Pending = 0, Free = 3
        Trunk Se0/1/1:23        Preference 13
                Member Timeslots : 1-24
                Total channels available : 23
                Data = 0, Voice = 22, Modem = 0, Pending = 0, Free = 1
        Trunk Se0/2/0:23        Preference 14
                Member Timeslots : 1-24
                Total channels available : 23
                Data = 0, Voice = 22, Modem = 0, Pending = 0, Free = 1
        Trunk Se0/2/1:23        Preference 15
                Member Timeslots : 1-24
                Total channels available : 23
                Data = 0, Voice = 19, Modem = 0, Pending = 0, Free = 4

        Total calls for trunk group: Data = 0, Voice = 103, Modem = 0
                                     Pend = 0, Free = 35

        advertise_flag 0x00000040, capacity timer 25 sec tripl_config_mask 0x00000000
        AC_curr 29, FD_curr 80, SD_curr -40

        succ_curr 1397 tot_curr 1498
        succ_report 1397 tot_report 1498
        changed 1 replacement position 0

-----Original Message-----
From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Jonathan Charles
Sent: Friday, September 11, 2009 9:51 AM
To: RAWLE GORDON
Cc: cisco-voip at puck.nether.net 
Subject: Re: [cisco-voip] PRI Trunk Group H323

The trunk group is for analog only...

You will need to duplicate your peers and create preferences for each....

This way you don't have glare and you can order your outgoing calls to
the last PRI in the telco trunk group.

Jonathan

On Fri, Sep 11, 2009 at 10:45 AM, RAWLE GORDON <ragordon at mtb.com> wrote:
> Hi there,
> I'm looking for any information on configuring more that a single PRI, in a 28XX or 38XX using the H323 protocol. I'm able to locate configuration for FXOs but not PRI that works anyway. My router/gateway IOS is 12.4 (20) T2. Is this even doable ?
>
> Any assistance/thoughts would be much appreciated .....
>
> Thanks in advance,
> Tony Gordon
> Voice Communications
> M&T Bank
> 410-347-6010
>
>
>
> ************************************
> This email may contain privileged and/or confidential information that is intended solely for the use of the addressee.  If you are not the intended recipient or entity, you are strictly prohibited from disclosing, copying, distributing or using any of the information contained in the transmission.  If you received this communication in error, please contact the sender immediately and destroy the material in its entirety, whether electronic or hard copy.  This communication may contain nonpublic personal information about consumers subject to the restrictions of the Gramm-Leach-Bliley Act and the Sarbanes-Oxley Act.  You may not directly or indirectly reuse or disclose such information for any purpose other than to provide the services for which you are receiving the information.
> There are risks associated with the use of electronic transmission.  The sender of this information does not control the method of transmittal or service providers and assumes no duty or obligation for the security, receipt, or third party interception of this transmission.
> ************************************
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net 
> https://puck.nether.net/mailman/listinfo/cisco-voip 
>
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net 
https://puck.nether.net/mailman/listinfo/cisco-voip 

 NOTICE: This email message is for the sole use of the intended recipient(s) and may contain confidential and privileged information. Any unauthorized review, use, disclosure or distribution is prohibited. If you are not the intended recipient, please contact the sender by reply email and destroy all copies of the original message.

************************************
This email may contain privileged and/or confidential information that is intended solely for the use of the addressee.  If you are not the intended recipient or entity, you are strictly prohibited from disclosing, copying, distributing or using any of the information contained in the transmission.  If you received this communication in error, please contact the sender immediately and destroy the material in its entirety, whether electronic or hard copy.  This communication may contain nonpublic personal information about consumers subject to the restrictions of the Gramm-Leach-Bliley Act and the Sarbanes-Oxley Act.  You may not directly or indirectly reuse or disclose such information for any purpose other than to provide the services for which you are receiving the information.
There are risks associated with the use of electronic transmission.  The sender of this information does not control the method of transmittal or service providers and assumes no duty or obligation for the security, receipt, or third party interception of this transmission.
************************************