[cisco-voip] is all traffic endpoint initiated?
Ryan Ratliff
rratliff at cisco.com
Tue Aug 10 16:12:59 EDT 2010
I am talking about the software resources and am glad that you do have them. I was worried for a second that there was another DMA bug where you didn't get them created.
In 4.x you had the ability to remove these resources from the database. That is changed in the appliance versions and they are there whether you like them or not. This is to prevent them from causing transient connections for the service being activated but the resources not being in the database.
-Ryan
On Aug 10, 2010, at 3:58 PM, Lelio Fulgenzi wrote:
OK - I'm a bit lost here, what do you mean by "software media resources" ? What exactly am I trying to add? Are you talking about software based annunciators, conference bridges and MTPs? I deleted these all in my v4 cluster.
But when I take a look at my v7 pub I now see them again:
6 Annunciators (ANN_2 thru ANN_7, one for each pub and sub with the correct IP addr)
6 Conference Bridges (CFB_2 thru CFB_7, one for each pub and sub with the correct IP addr)
in addition to my hardware conference bridges
6 MTPs (MTP_2 thru MTP_7, one for each pub and sub with the correct IP addr)
MTP_6 is replaced with UOGCCM106_MTP the MTP I had in my v4.1 cluster
With each of them, the resource assigned to the pub is registered.
I'm in the midst of installing one subscriber and we'll see if it registers as well.
What do you think?
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Cooking with unix is easy. You just sed it and forget it.
- LFJ (with apologies to Mr. Popeil)
From: "Ryan Ratliff" <rratliff at cisco.com>
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>
Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net>
Sent: Tuesday, August 10, 2010 3:42:38 PM
Subject: Re: [cisco-voip] is all traffic endpoint initiated?
Regardless of whether IPVMSA is activated or not you should have the software media resources in the database already. They are added when you add the server to system->server and cannot be deleted.
In your case see if you can add them manually in 7.x. If not go back and add them in 4.x and re-DMA. If you can add them in 7.x and they register then there should be no reason to re-run DMA.
-Ryan
On Aug 10, 2010, at 12:01 PM, Lelio Fulgenzi wrote:
Ryan, I'm just reviewing this last note from you.
I do have "Cisco IP Voice Media Streaming App" activated on the publisher, but I don't have any software resources configured on the publisher. I have hardware conference resources (6608 ports) and an MTP configured on another subscriber that has no dependencies.
There's also the default music on hold sources but they are not being used.
Think I should be safe? Or should I go through the upgrade/DMA again, deactivate IPVMSA, then change the IP addresses?
---
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Cooking with unix is easy. You just sed it and forget it.
- LFJ (with apologies to Mr. Popeil)
From: "Ryan Ratliff" <rratliff at cisco.com>
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>
Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net>
Sent: Tuesday, November 10, 2009 9:44:43 AM
Subject: Re: [cisco-voip] is all traffic endpoint initiated?
That is correct. Be aware that the software media resources on the publisher will still be trying to contact the old subscribers (based on cm group) if the IPVMSA service is activated before you change the IP addresses in the database. I would strongly recommend you make this change prior to activating any services.
-Ryan
On Nov 9, 2009, at 6:58 PM, Lelio Fulgenzi wrote:
OK. So in my instance, after I go through the DMA import onto the new publisher hardware (with new IP address), I can edit the existing callmanager servers (listed as IP addresses) and replace them with the new/different IP addresses of the new subscribers. Then when I install the new subscribers, I make sure to use the IP address not the hostname.
I'm essentially going from a cluster with the following:
pub : 10.104.20.105
tftp: 10.104.96.106
sub1: 10.104.20.101
sub2: 10.104.20.103
sub3: 10.104.96.104
sub4: 10.104.96.108
to a cluster (all new hardware) with the following:
pub : 10.104.91.105
tftp: 10.104.91.205
sub1: 10.104.91.103
sub2: 10.104.91.203
sub3: 10.104.91.104
sub4: 10.104.91.204
I'm working from the assumption that it's better to edit the servers than it is to delete them from the configs because of all the work that is involved, i.e. changing ccm groups, park numbers, etc.
---
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"Bad grammar makes me [sic]" - Tshirt
----- Original Message -----
From: "Ryan Ratliff" <rratliff at cisco.com>
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>
Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net>
Sent: Monday, November 9, 2009 6:43:53 PM GMT -05:00 US/Canada Eastern
Subject: Re: [cisco-voip] is all traffic endpoint initiated?
The most important point is that the value in system->server should always match that of the server, whether it is IP address or hostname. Just because you haven't configured DNS on the servers doesn't mean the hostname in this field will break things.
-Ryan
On Nov 9, 2009, at 3:48 PM, Lelio Fulgenzi wrote:
Thanks Ryan. If I understand you correctly then:
if I simply change the value in the system > server fields, i should change them from IP address to hostname, but
if I delete and recreate, I can use IP addresses?
I think I got that straight.
---
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"Bad grammar makes me [sic]" - Tshirt
----- Original Message -----
From: "Ryan Ratliff" <rratliff at cisco.com>
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>
Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net>
Sent: Monday, November 9, 2009 3:45:06 PM GMT -05:00 US/Canada Eastern
Subject: Re: [cisco-voip] is all traffic endpoint initiated?
See below...
-Ryan
On Nov 9, 2009, at 11:46 AM, Lelio Fulgenzi wrote:
Thanks for your comments Ryan and Justin. They'll definitely help me build my new cluster. Some comments/questions:
Ryan: I'm a little concerned with using hostnames and not IP address in the System -> Server settings. Do you mean IP addresses don't match what's on the box on the other side? In the event of a DNS failure I don't want my phone system to go down. I understand that there will be more and more dependancies, but I'd like to minimize them.
RR> Whenever you change the IP address of a CUCM server if the IP address of the server does not match the processNode entry in the database (System->Server) then the database won't start and bad things happen. With the hostname being in System->Server then the IP address will always match.
My recommendation was specific to the IP address change procedure, just to make sure that everything comes up.
Ryan: I'm a little confused as to you what you mean by your last paragraph. How can I use hostnames if I haven't configured DNS? Won't it come back with errors?
The CUCM subscribers know the publisher's IP address because you configure it during installation. The clustermanager serivce on each server is responsible for connecting and updating each server's local hosts file so that name resolution always works within the cluster, regardless of whether DNS is configured.
Justin: I would think it would be cleaner to delete and recreate rather than simply edit.
To all:
how many are using hostnames rather than IP addresses in the System -> Server settings?
has anyone had to rename/delete a subscriber using Justin's suggested method?
Thanks again....
----- Original Message -----
From: "Ryan Ratliff" <rratliff at cisco.com>
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>
Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net>
Sent: Monday, October 26, 2009 10:53:19 AM GMT -05:00 US/Canada Eastern
Subject: Re: [cisco-voip] is all traffic endpoint initiated?
Don't worry about network connectivity for accessing the DMA files, since that's going to be during the install and no services will be running to either accept connections or initiate them.
When changing the IP address I'd highly recommend your System->Server entries be hostnames and not IP addresses, since bad things happen when the IP address in System->Server doesn't match the one that's actually on the box.
You are correct that you don't have to configure DNS or NTP until after everything is built. In fact unless you are going to have a DNS server on the dead network then you will cause problems by configuring a DNS server.
Since the servers get their hosts files configured during the sub install as long as no DNS is configured and your System->Server entries are hostnames then you can leave the new servers on a live network (just with different IPs than the production servers). They won't talk to anything they can't resolve and without DNS the only thing they will resolve is the other nodes of the cluster. You'll want to watch out for multicast MOH if you do this, but otherwise it should be safe.
The rest of your procedure looks fine, maybe a bit of overkill, but definitely the safe way to go.
-Ryan
----- Forwarded Message -----
From: "Justin Steinberg" <jsteinberg at gmail.com>
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>
Cc: "Ryan Ratliff" <rratliff at cisco.com>, "cisco-voip voyp list" <cisco-voip at puck.nether.net>
Sent: Monday, October 26, 2009 10:16:28 AM GMT -05:00 US/Canada Eastern
Subject: Re: [cisco-voip] is all traffic endpoint initiated?
Lelio,
Are you planning to use new IP addresses for the entire cluster? if so, I would do install the new publisher via DMA, select to use a new IP address on a new isolated VLAN that doesnt have connectivity to your production environment. Then once the ccmadmin page is up for the new publisher, just go into the system>server menu and change the IP addresses from the current 4.1/production IPs to the new addresses you've allocated to the new cluster. Once you've changed the IPs of the subscribers, I would reboot the system and then you should be fine to put it on the production network.
Renaming the IPs is much easier than deleting and recreated - since when you delete you have to rebuild all the dependencies, etc. I've also had problems in the past with the old server names / IPs staying around in some system configuration files that have required TAC assistance to root in and manually edit these files.
Justin
On Oct 23, 2009, at 11:08 PM, Lelio Fulgenzi wrote:
Thanks Ryan,
Our plan was to:
install the new publisher using DMA with a new IP address on a new VLAN
reconfigure callmanager groups so they all use the publisher and only the publisher
delete call park numbers on all subscribers
remove all previous subscriber information from the new publisher
start installing the new subscribers
rebuild callmanager groups and call park numbers
I'm not sure how I can do that on a dead network, since the install process goes out and does DNS tests and NTP tests etc. Plus I need to access my DMA upgrade file too, right?
I guess I could skip enabling DNS, NTP, etc, until just before step 5 once I put the publisher on a live network, and perform steps 1 thru 4 on an isolated VLAN with SFTP access to my DMA file?
What do you think?
---
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"Bad grammar makes me [sic]" - Tshirt
----- Original Message -----
From: "Ryan Ratliff" <rratliff at cisco.com>
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>
Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net>
Sent: Friday, October 23, 2009 10:14:35 PM GMT -05:00 US/Canada Eastern
Subject: Re: [cisco-voip] is all traffic endpoint initiated?
The CUCM servers themselves initiate connections to each other and I have seen post-DMA servers initiating connections (SDL, media resources) to the 4.x servers because they were reachable. I'd highly advise keeping your post-DMA servers on a dead-net until you can get new IP addresses on them.
-Ryan
On Oct 23, 2009, at 8:53 PM, Lelio Fulgenzi wrote:
We are planning on building a new 7.1 cluster using DMA. I want to make sure that we don't cause any service interruptions in our production network. Can anyone confirm that any traffic, i.e. registration is end point initiated? We only have SCCP and MGCP and SRST devices out there. There's no reason for the new cluster to try to talk to any of the devices out there is there?
---
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"Bad grammar makes me [sic]" - Tshirt
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100810/7f0b1934/attachment.html>
More information about the cisco-voip
mailing list