[cisco-voip] Monitoring Pri Usage

[kevin.hobson2000 at ntlworld.com]

Hi Cumhur,

I used the other OID that you advised to use and i am now seeing it flagged both on debugs and in the syslog.

Thanks for your help.

Kev

---- Cumhur Kizilari <yahoo at cumhur.com> wrote: 
> Hi Kevin,
> 
> Have you tried this OID ? 1.3.6.1.4.1.9.10.19.1.1.4.0 because it's different
> OID.
> 
> You are using 1.3.6.1.4.1.9.10.19.1.1.11  this one, please  try to make it
> simple and download STG write your IP address and community change  OID
> string with this OID 1.3.6.1.4.1.9.10.19.1.1.4.0  and check is it working or
> not.
> 
> Regards,
> Cumhur
> 
> On Wed, Feb 10, 2010 at 12:10 PM, <kevin.hobson2000 at ntlworld.com> wrote:
> 
> > Hi Cumhur,
> >
> > I have added a .0 to then of the oid which has stopped the error in the
> > debug.
> >
> > See below:
> >
> > Feb 10 09:43:17.774: fh_process_async: re=463448F0, timer_type=POLL
> > Feb 10 09:43:17.774: snmp_value_uint_compare:op1=0 op2=2 ret=FALSE
> > Feb 10 09:43:17.774: snmp_entry_value_check:Returning FALSE
> > Feb 10 09:43:17.774: fh_process_async: update_t=0cron_tick: num_matches 0
> >
> >
> > The problem i have now is that this is still not being flagged in the log
> > when calls rise above 2.
> >
> > Thanks
> >
> > Kev
> >
> >
> > ---- Cumhur Kizilari <yahoo at cumhur.com> wrote:
> > > Hi Kevin,
> > >
> > > I'm using IOD "1.3.6.1.4.1.9.10.19.1.1.4.0" cpmActiveDS0s  for PRI active
> > > calls monitoring.
> > >
> > > Maybe this OID can helps you. You can test using STG (
> > > http://www.wtcs.org/informant/stg.htm)  or use  free (10 sensors ) PRTG
> > > http://www.paessler.com/prtg/download
> > >
> > > Best Regards,
> > > Cumhur
> > >
> > > On Tue, Feb 9, 2010 at 10:38 AM, <kevin.hobson2000 at ntlworld.com> wrote:
> > >
> > > > Hi,
> > > >
> > > > I am trying to use Embedded Event Manager to flag  when calls on a pri
> > get
> > > > above 28 but its not working.  I found an OID which shows number of
> > calls
> > > > currently on the B Channels of a pri.  I dropped the threshold to two
> > just
> > > > to check it was functioning correctly.  Config below:
> > > >
> > > > event manager applet bchan-mon
> > > >  event snmp oid 1.3.6.1.4.1.9.10.19.1.1.11 get-type exact entry-op gt
> > > > entry-val 2 poll-interval 60
> > > >  action exceeded syslog priority critical msg "All Chanels in Use"
> > > >
> > > >
> > > > I have done a debug and it says the OID is not found even though if i
> > do a
> > > > show snmp mib i see the OID.  Output below:
> > > >
> > > > Feb  9 08:35:58.097: fh_process_async: re=445EF694, timer_type=POLL
> > > > Feb  9 08:35:58.097: snmp_entry_value_check: OID unavailable, value
> > check
> > > > skipped
> > > > Feb  9 08:35:58.097: snmp_entry_value_check:Returning FALSE
> > > > Feb  9 08:35:58.097: fh_process_async: update_t=0cron_tick: num_matches
> > 0
> > > >
> > > >
> > > > Has anyone successfullly used EEM to do this?
> > > >
> > > > Any help appreciated.
> > > >
> > > > Thanks
> > > >
> > > > Kev
> > > > _______________________________________________
> > > > cisco-voip mailing list
> > > > cisco-voip at puck.nether.net
> > > > https://puck.nether.net/mailman/listinfo/cisco-voip
> > > >
> >
> >