[cisco-voip] SIP Trunk from ISP DTMF issue

Matt Slaga (US) Matt.Slaga at us.didata.com
Tue Jul 13 11:54:24 EDT 2010


If you are not using a cube, you might need an enhanced IOS software MTP termination point which will allow the capturing of DTMF packets inband and process them out of band.  These can run as software MTPs on the gateway (cannot use the UCM built in software MTPs for this purpose).

________________________________________
From: cisco-voip-bounces at puck.nether.net [cisco-voip-bounces at puck.nether.net] On Behalf Of Nick Matthews [matthnick at gmail.com]
Sent: Tuesday, July 13, 2010 11:38 AM
To: Mark Holloway
Cc: cisco-voip at puck.nether.net; Paul van den IJssel
Subject: Re: [cisco-voip] SIP Trunk from ISP DTMF issue

Also check the ccn subsystem sip on the CUE - make sure you're
configured for the DTMF method you're using everywhere else.  Plus use
a CUBE as stated.

-nick

On Tue, Jul 13, 2010 at 11:17 AM, Mark Holloway <mh at markholloway.com> wrote:
> The Genband is probably doing the same thing that CUBE would be doing.  What
> are the DTMF requirements from your provider?  Have you confirmed that DTMF
> is being passed to the provider?  A Wireshark capture on the public side of
> the S3 would verify DTMF is being passed.
> On Jul 13, 2010, at 7:58 AM, Bill wrote:
>
> You should not trunk directly to CUCM from your ITSP. You need to go through
> a CUBE router. Terminate the ITSP on the CUBE and then do a SIP trunk to
> your CUBE router.
>
> ________________________________
> From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On
> Behalf Of Paul van den IJssel
> Sent: Tuesday, July 13, 2010 9:54 AM
> To: cisco-voip at puck.nether.net
> Subject: [cisco-voip] SIP Trunk from ISP DTMF issue
>
> Hi all,
>
> Currently I'm running a acceptance test on a SIP Trunk from our ISP.
> Everything is working fine except the DTMF.
>
> Setup:
> [GenBand SBC] ---- [SIP Trunk into CUCM 7.1] ---- [Cisco Unity Express 7.0]
>
> The SIP Trunk as well as the CUE are in the same region supporting only
> G.711. On the SIP Trunk I've tried all different kind of DTMF configurations
> (No Preference, RFC 2833 and OOB). We've tried to force the GenBand SBC to
> only use RFC 2833 as well as the SIP Trunk. But this didn't work, not even
> after we added a MRGL with MTP's.
>
> Is there some sort of best practive to implement DTMF over a SIP Trunk? Is
> there a way I can do some debugging on the CUCM/CUE?
>
> Kind regards,
>
> Paul van den IJssel
> Digacom
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip

-----------------------------------------
Disclaimer: 

This e-mail communication and any attachments may contain
confidential and privileged information and is for use by the
designated addressee(s) named above only.  If you are not the
intended addressee, you are hereby notified that you have received
this communication in error and that any use or reproduction of
this email or its contents is strictly prohibited and may be
unlawful.  If you have received this communication in error, please
notify us immediately by replying to this message and deleting it
from your computer. Thank you.



More information about the cisco-voip mailing list