[cisco-voip] Modify calling number without showing on screen

[Ryan Ratliff]

Where are you doing the prefixing and discarding?  Look below in the email thread and you'll see where it's pointed out that modifications within a route list won't show up on the phone.  Modifications via translation pattern or route pattern will.

-Ryan

On Jul 29, 2010, at 12:49 PM, Jefflin Choi wrote:

Hi,

I set the  'Always Display Original Dialed Number' parameter under CCM
Service Parameters and got what i expected but discarded digits are
now shown on phone display.

Anyway around the issue?

Thanks in advance.
Jeff

On 7/30/10, Jefflin Choi <jefflin.choi at gmail.com> wrote:
> Hi,
> 
> I'm actually encountering the same problem. Tried setting "Block
> Connected Number IE" to TRUE but didn't work.
> 
> My setup is prefix a number to the route pattern for the gateway and
> whenever a phone dials a number, the prefix'd number appeared on the
> phone together with the called number.
> 
> I'm using the prefix for the gateway to determine which voice port to use.
> Using one gateway for multiple route pattern with different prefix
> numbers per route-pattern.
> 
> Any chance i might hide the prefix'd number on the phone display when
> trying to make a call?
> 
> Thanks,
> Jeff
> 
> On 1/23/10, Ali El Moussaoui <mousawi.ali at gmail.com> wrote:
>> thanks Ryan .. that did the job ..perfect! I set the service parameter
>> "Block Connected Number IE" to TRUE and did the translation on the
>> gateway
>> .. Its working like charm. Thanks ;)
>> 
>> On Fri, Jan 22, 2010 at 5:35 PM, Ryan Ratliff <rratliff at cisco.com> wrote:
>> 
>>> If you modify it at the gateway does it show immediately or after the
>>> call
>>> is connected?  I'd guess the gateway is sending CUCM a connected party
>>> IE
>>> and that will always update the phone's display.    I don't know if you
>>> can
>>> block it at the router but there is a service parameter in CUCM to block
>>> this IE "Block Connected Number IE" (advanced cucm parameter).
>>> 
>>> -Ryan
>>> 
>>> On Jan 22, 2010, at 10:01 AM, Ali El Moussaoui wrote:
>>> 
>>> thats exactly my problem.. I am doing called transformation at thr route
>>> pattern level.. I dnt want to use digit strip since i need the digits at
>>> the
>>> gateway. I tried to add prefix and tryied the mask both had same result.
>>> I
>>> even tried to match on the gateway dial-peers and change before sending
>>> to
>>> PSTN but the modified number shows again again after translation!!!
>>> 
>>> On Fri, Jan 22, 2010 at 4:57 PM, Ryan Ratliff <rratliff at cisco.com>
>>> wrote:
>>> 
>>>> Anything you modify past the route pattern won't show up on the phone
>>>> (ie
>>>> strip digits at route pattern, phone updates; strip digits in route
>>>> list
>>>> details, phone doesn't show it).  The exception may be transformations
>>>> applied at the outbound gateway.  Those may result in the modified
>>>> number
>>>> showing on the phone, but you'll want to test to be sure.
>>>> 
>>>> -Ryan
>>>> 
>>>>  On Jan 22, 2010, at 5:06 AM, Ali El Moussaoui wrote:
>>>> 
>>>> sorry i meant Called Number
>>>> 
>>>> On Fri, Jan 22, 2010 at 11:54 AM, Ali El Moussaoui
>>>> <mousawi.ali at gmail.com
>>>>> wrote:
>>>> 
>>>>> Hello,
>>>>> 
>>>>> Is it possible to modify the calling number without being shown on the
>>>>> phone screen or showing some other number?
>>>>> 
>>>>> Regards,
>>>>> Ali
>>>>> 
>>>> 
>>>> _______________________________________________
>>>> cisco-voip mailing list
>>>> cisco-voip at puck.nether.net
>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>> 
>>>> 
>>> 
>>> 
>> 
>